Sort

Subaru Forester BH5 Front Wheel Hubs

KSh6,500.00
Component Part Numbers & Fitment
  • OEM Wheel Hub Spindle Part Number: 28362AE001, 28362AE000
  • OEM Wheel Bearing Part Number: 28316FE000 (Double-row angular contact ball bearing / tapered roller bearing)
  • OEM Inner Oil Seal (Axle Side): 28015AA070
  • OEM Outer Oil Seal (Wheel Side): 28015AA080
  • Chassis Application: BH5 JDM variants including Brighten, TX, TS-R, and GT-B E-Tune (EJ202, EJ204, and Twin-Turbo EJ208 platforms).
Physical & Dimensional Specifications
  • Wheel Bolt Pattern (PCD): 5 x 100 mm
  • Hub Flange Outer Diameter: 124 mm
  • Wheel Stud Bolt Size: M12 x 1.25
  • Input Shaft Spline Count (Drive Axle Interface): 27 Teeth
  • Bearing Inner Diameter: 42 mm
  • Bearing Outer Diameter: 72 mm
  • Bearing Width: 38 mm (Inner track) / 35 mm (Outer track) [1]
Tightening Torque Specifications
  • Front Axle Center Locknut: 137 ft-lbs (186 N·m) (Note: Always use a new axle nut and peen the locking collar firmly into the axle shaft slot after torquing).
  • Strut-to-Steering Knuckle Clevis Bolts (2x 19mm): 129 ft-lbs (175 N·m) (The upper bolt features an eccentric cam lobe used to set front camber alignment).
  • Lower Ball Joint Pinch Bolt (to Knuckle Base): 37 ft-lbs (50 N·m) [1]
  • Tie Rod End Castle Nut to Knuckle Assembly: 19 ft-lbs (26 N·m) (Tighten up to 22 ft-lbs max only to align cotter pin window).
  • Brake Caliper Torque Bracket-to-Knuckle Bolts: 59 ft-lbs (80 N·m) [1]
  • Front Wheel Lug Nuts: 89 ft-lbs (120 N·m)

Subaru Forester SG5 Front Wheel Hubs

KSh6,500.00
Component Part Numbers & Fitment
  • OEM Wheel Hub Spindle Part Number: 28362AE001, 28362AE000
  • OEM Wheel Bearing Part Number: 28316FE000 (Double-row angular contact ball bearing / tapered roller bearing)
  • OEM Inner Oil Seal (Axle Side): 28015AA070
  • OEM Outer Oil Seal (Wheel Side): 28015AA080
  • Chassis Application: SG5 2.0L N/A (EJ202), 2.0XT Turbo (EJ205), and cross-compatible JDM/Cross Sports variants.
Physical & Dimensional Specifications
  • Wheel Bolt Pattern (PCD): 5 x 100 mm
  • Hub Flange Outer Diameter: 124 mm
  • Wheel Stud Bolt Size: M12 x 1.25
  • Input Shaft Spline Count (Drive Axle Interface): 27 Teeth
  • Bearing Inner Diameter: 42 mm
  • Bearing Outer Diameter: 72 mm
  • Bearing Width: 38 mm (Inner track) / 35 mm (Outer track) [1, 2]
Tightening Torque Specifications
  • Front Axle Spindle Center Locknut: 137 ft-lbs (186 N·m) (Note: Always use a new axle nut and peen the locking collar firmly into the axle shaft slot after torquing).
  • Strut-to-Steering Knuckle Clevis Bolts (2x 19mm): 129 ft-lbs (175 N·m) (The upper bolt features an eccentric cam lobe used to set front camber alignment). [1, 2]
  • Lower Ball Joint Pinch Bolt (to Knuckle Base): 37 ft-lbs (50 N·m) [1, 2]
  • Tie Rod End Castle Nut to Knuckle Assembly: 19 ft-lbs (26 N·m) (Tighten up to 22 ft-lbs max only to align cotter pin window). [1]
  • Brake Caliper Torque Bracket-to-Knuckle Bolts: 59 ft-lbs (80 N·m) [1]
  • Front Wheel Lug Nuts: 89 ft-lbs (120 N·m)[1]

Subaru Legacy B4 Bilstain Shocks

KSh8,000.00
Damper Core Technology & Design
  • Front Internal Layout: Upside-down (Inverted) Monotube Gas Pressure strut assembly (Bilstein patented setup for extreme structural rigidity under high cornering loads).
  • Rear Internal Layout: Standard Monotube Gas Pressure or Twin-tube (Variant-dependent, e.g., standard B4 replacement). [1, 2]
  • Damping Mechanism: Self-adjusting multi-stage valving (degressive piston design provides higher damping force at low speeds for chassis control, and softer force at high speeds to absorb bumps).
  • Gas Type: High-pressure Nitrogen charged to prevent fluid cavitation/foaming under rapid cycling. [1, 2]
OEM Reference Part Numbers (JDM Legacy B4 Spec-B BL5/BP5)
  • Front Right (Inverted Monotube): 20310AG420 / VE3-B831 (Bilstein B6 Heavy Duty alternate)
  • Front Left (Inverted Monotube): 20310AG430 / VE3-B832
  • Rear Damper Assembly: 20365AG260 / BE5-B833
  • Standard Bilstein Aftermarket B4 Line (Non-Inverted OE Replacement): Front Right: 22-165572 | Rear: 19-158686. [1, 2]
Physical Dimensions (Bilstein Rear B4 Example)
  • Collapsed Length: 255.5 mm (10.06 in)
  • Extended Length: 400.5 mm (15.77 in)
  • Stroke Profile: Shortened travel window on JDM B4 Spec-B models compared to the standard USDM non-Bilstein Legacy chassis.
  • Lower Mount Interface: Eyelet bushing
  • Upper Mount Interface: Stem thread [1]
Chassis Interface & Torque Specifications
  • Front Upper Strut Top Hat Mount Nuts (3x): 14.5 ft-lbs (20 N·m)
  • Front Strut Piston Center Top Nut: 41 ft-lbs (56 N·m)
  • Front Lower Strut Mount Clevis Bolts (to Knuckle - 2x): 114 to 129 ft-lbs (155 to 175 N·m) (Note: Upper bolt functions as the factory camber eccentric alignment cam).
  • Rear Upper Strut Top Hat Mount Nuts: 22 ft-lbs (30 N·m)
  • Rear Lower Strut Mount-to-Trailing Arm Bolt: 88.5 to 110 ft-lbs (120 to 150 N·m) [1, 2]
Factory Spring Rates (Spec-B Bilstein Pairings)
  • Front Spring Rate: ~3.2 kg/mm to 3.8 kg/mm (Linear rate configuration)
  • Rear Spring Rate: ~4.0 kg/mm to 4.8 kg/mm (Progressive/Linear multi-link arrangement) [1]

Subaru Forester SG5 Rear Shocks

KSh10,000.00
1. Core & Dimensional Specifications
  • Design Type: Gas-pressure suspension strut assembly incorporating an integrated lower spring seat. [1]
  • Internal Construction: Standard replacement units (such as the premium Japanese JDM-spec KYB Excel-G series) utilize a low-pressure nitrogen gas-charged twin-tube system to eliminate oil aeration and foaming during rough driving. [1, 2]
  • Mounting Interfaces:
    • Top Mount: Three-bolt upper top hat pin mount (M8 studs) matching the rear strut tower body.
    • Bottom Mount: Double-bolt bottom clamp clevis bracket that sandwiches directly onto the rear wheel hub/knuckle assembly. [1, 2]
  • Key Measurements (Standard KYB 334344/334345 specs):
    • Extended Length: ~610 mm
    • Collapsed Length: ~415 mm
    • Piston Stroke Travel: ~195 mm
2. The Self-Leveling Suspension (SLS) vs. Standard Setup
Many JDM/Ex-Japan SG5 models arrived equipped with SLS struts, which feature a wider body cylinder housing a built-in hydraulic pump mechanism. This internal pump relies on the vehicle’s natural bouncing motion to pump fluid and raise the rear to standard ride height under heavy cargo loads.
  • The SLS Failure Issue: When the internal seals fail, the vehicle's rear end sags significantly.
  • The Conversion Metric: Because replacement OEM SLS struts are highly expensive, many owners convert to standard struts (like KYB 334344 / 334345). Crucial Note: If converting from SLS to standard shocks, you must also replace the rear coil springs with stiffer, standard-matching coils. The original SLS coil springs are much softer and cannot support the vehicle's weight on standard non-SLS dampers alone. [1, 2, 3]
3. Genuine OEM & Brand Cross-Reference Numbers
  • Rear Left Hand (LH) Strut Assembly: 20360SA010, 20360SA050, 20360SA130 (KYB Aftermarket Cross: 334345 / 339150).
  • Rear Right Hand (RH) Strut Assembly: 20360SA000, 20360SA040, 20360SA120 (KYB Aftermarket Cross: 334344 / 339149). [1, 2, 3]
4. Factory Torque Specifications
Important: To prevent premature bushing binding and twisting, snug all fasteners while the car is raised, lower the vehicle completely until it sits under its own weight (at ride height), and apply the final torque settings. [1, 2]
Fastener Connection Profile Metric Spec (N·m) Imperial Spec (ft-lbs)
Lower Strut-to-Knuckle Bolts (2 large M14 bolts per side) 200 N·m 145 ft-lbf
Upper Strut Tower Top Hat Nuts (3 per side inside the cabin) 30 N·m 22 ft-lbf
Central Piston Shaft Top Lock Nut 60 N·m 44 ft-lbf
Rear Sway Bar End Link Nuts 45 N·m 33 ft-lbf

Subaru Impreza GG2 Rear Shocks

KSh10,000.00
Component & Material Specifications
  • Right Hand (RH) Engine Mount (Timing Side):
    • Type: Hydraulic (Hydro-filled) dampening insulator.
    • Function: Houses an internal fluid chamber that dampens engine movement and prevents low-frequency idle vibration from passing into the cabin frame. This is crucial for smoothing out the natural imbalances of the 3-cylinder turbo variants.
    • Body Material: Die-cast aluminum alloy bracket joined to a stamped steel chassis anchoring flange.
  • Left Hand (LH) Transmission Mount (Gearbox Side):
    • Type: Compressed rubber-to-metal bonded cushion insulator.
    • Function: Suspends the 5-speed manual, 6-speed automatic, or CVT gearbox housing securely onto the left-hand subframe frame rail.
  • Rear Torque Rod (Lower Engine Pitch Stopper):
    • Type: "Dog-bone" structural link assembly.
    • Function: Limits fore-and-aft engine rotational pitching during sudden throttle changes, clutch engagement, and heavy braking.
Genuine Suzuki OEM Part Numbers
Part numbers vary based on engine type, transmission pairing (Manual vs. CVT), and whether it is a standard hatchback or a Swift Sport variant. Core OEM production part numbers include:
  • Right Hand (RH) Hydraulic Engine Mount: 11610-52R00 / 11610-68R00
  • Left Hand (LH) Transmission Mount Assembly: 11620-52R00 / 11620-68R10
  • Rear Lower Torque Rod / Stopper: 11710-52R00 / 11710-68R00
Factory Fastener Torque Specifications
Important: To avoid twisting the vulcanized rubber compounds out of their neutral resting positions, support the engine weight with an under-hoist support stand or floor jack. Fully lower the vehicle's weight onto its suspension before applying final torque settings to the primary chassis fasteners.
Fastener Connection Profile Metric Spec (N·m) Imperial Spec (ft-lbs)
RH Engine Mount Central Through-Bolt (to Engine Bracket) 85 N·m 63 ft-lbf
RH Mount-to-Chassis Frame Bolts 50 N·m 37 ft-lbf
LH Transmission Mount Center Nut/Bolt 80 N·m 59 ft-lbf
Rear Torque Rod Frame Through-Bolts 90 N·m 66 ft-lbf

Subaru Forester SG5 Steering Rack Ex-Japan

KSh10,000.00
Core Mechanical & Architectural Specifications
  • Steering Mechanism Design: Hydraulic Power Assisted Rack and Pinion Steering Gear Assembly.
  • Drive Configuration Layout: Engineered strictly for Right-Hand Drive (RHD) Japanese Domestic Market (JDM) chassis profiles.
  • Steering Wheel Ratio Responsiveness:
    • Standard Cross Sports / XT trims: 3.0 turns lock-to-lock.
    • STI Variant (SG9/SG5 specialized upgrade swap): 2.5 turns lock-to-lock (Quick-steer rack configuration).
  • Casing Housing Composition: High-strength die-cast Aluminum alloy body with integrated steel mounting sleeve eyelets.
  • Tie Rod Thread Metric: M16 x 1.5 inner tie rod housing thread.
  • Input Pinion Shaft Splines: 36 Teeth spline profile matching the steering column intermediate U-joint yoke.
Hydraulic Control & Pressure Profiles
  • Fluid Compatibility: Dexron II / Dexron III or specialized Subaru Power Steering Fluid (Mineral-based hydraulic oil matrix).
  • Maximum Line Operating Pressure: 8.3 to 9.2 MPa (83 to 92 Bar) at maximum pump load.
  • Valve Architecture: Internal rotary control valve with dynamic torsion bar feedback to meter hydraulic fluid flow relative to driver steering wheel input speed.
Factory Genuine JDM OEM Cross-Identification
Depending on production dates (Pre-facelift 2002–2005 vs. Facelift 2005–2007) and whether the chassis is a naturally aspirated EJ202 or turbo EJ205, "Ex-Japan" imports pull from these official codes:
  • Primary OEM Reference Root Numbers: 34110SA080, 34110SA090, 34110SA110, 34110SA000.
  • Aftermarket Parts Blueprint Index:
    • Sankei 555 Core Rack Ends: SR-6300.
    • Sankei 555 Outer Tie Rod Ends: SE-6301.
Environmental Sealing & Isolation Components
  • Fluid Seal Profile: High-durability Nitrile rubber (NBR) dynamic inner shaft seals and dual-lip pinion oil rings.
  • Protective Bellows: Heat-treated, oil-resistant Chloroprene rubber (CR) dust boots clamped via spring-steel retention clips to prevent water ingestion into internal gear tracks.

Subaru Impreza GP2 Shock Mountain

KSh3,500.00
Front Strut Top Mount Specifications
    • Mounting Configuration: 3-bolt upper triangular tower mounting footprint.
    • Chassis Isolator Construction: Heavy-duty vulcanized shore-hardness rubber chemically bonded to a stamped structural steel core casing.
    • Integrated Bearing Profile: Heavy-duty internal axial thrust ball bearing mechanism integrated within the rubber seat to facilitate smooth, unbinding rotation of the MacPherson strut during steering inputs.
    • Axle Symmetry: Symmetrical, non-directional layout (same component services both the Front Left Hand and Front Right Hand strut assemblies).
    • Subaru Factory Genuine OEM Part Numbers: 20320FG012, 20320FG013, 20320FG002.
    • Factory Hardware Installation Torques:
        • Chassis Tower Flange Nuts (3 per mount): 20 Nm (14.5 ft-lbs).
        • Center Piston Rod Strut Nut: 55 Nm (41 ft-lbs).
Rear Shock Top Mount Specifications
  • Mounting Configuration: Dual-bolt (2-bolt) linear top-hat pin configuration.
  • Suspension Architecture Match: Specifically configured for the independent multi-link rear suspension platform utilized on the GP2 chassis.
  • Isolator Type: Isolated thick-sandwich rubber bushing damper configuration designed to suppress high-frequency road vibrations and Cabin NVH (Noise, Vibration, and Harshness).
  • Subaru Factory Genuine OEM Part Numbers: 20370FG012, 20370FJ001.
  • Factory Hardware Installation Torques:
    • Upper Chassis Fasteners (2 per mount): 30 Nm (22 ft-lbs).
    • Center Damper Shaft Retaining Nut: 25 Nm (18.4 ft-lbs).

Subaru Outback Model BP5 Bilstain Shocks

KSh8,000.00
Front Axle Bilstein Strut Specifications
  • Suspension Layout: Independent MacPherson Strut.
  • Internal Shock Architecture: Inverted Monotube (Upside-Down Technology). The piston rod is integrated inside the bottom axle casing, while the thicker outer tube acts as the structural slider. This drastically increases lateral rigidity under heavy cornering loads. [1]
  • Damping Medium: High-pressure nitrogen gas with a single-tube hydraulic fluid separation piston. [1]
  • Mounting Configuration: 3-bolt top pin hat assembly with a lower dual-bolt steering knuckle clamp layout. [1]
  • Damping Forces (Measured @ 0.52 m/s):
    • Compression Force: 1090 N
    • Rebound Force: 2460 N [1]
  • Orientation: Asymmetrical, side-specific left and right structures.
Rear Axle Bilstein Shock Specifications
  • Suspension Layout: Multi-Link Independent Rear Suspension.
  • Internal Shock Architecture: Standard Monotube (Gas Pressure).
  • Shock Design Type: Non-load-bearing telescopic damper (does not carry a spring seat; operates independently of the rear coil spring).
  • Lower Bushing Bushing Assembly OD: 40 mm (Specific to the BP/BL platform; thicker than later generation models).
  • Mounting Connections: Top Pin threaded rod | Bottom Eyelet sleeve through-bolt bushing. [1, 2, 3]
Factory OEM & Aftermarket Part Numbers
  • Bilstein Aftermarket Performance Upgrade (B6 Heavy Duty Series):
    • Front Right Hand (RH): 35-118312 (Alternative: VE3-3066RJ)
    • Front Left Hand (LH): 35-118305 (Alternative: VE3-3066LJ)
    • Rear Axle Dampers: 24-118323 [1, 2, 3]
  • Subaru Factory Genuine JDM OEM Numbers (Spec.B Baseline):
    • Front Right Hand (RH): 20310AG401, 20310AG424, 20310AG100
    • Front Left Hand (LH): 20310AG411, 20310AG434
    • Rear Axle Dampers: 20365AG274

Subaru Legacy Model BH5 Front Shocks

KSh5,000.00
Core Architectural Specifications
    • Suspension Type: Independent MacPherson Strut.
    • Strut Design: Structural Suspension Strut (acts as a load-bearing member).
    • Internal Construction: Gas-Charged Twin-Tube (low-pressure nitrogen gas).
    • Damping Medium: Hydraulic fluid with nitrogen gas charge to prevent aeration.
    • Mounting Configuration: 3-bolt top hat mount chassis connection with a bottom dual-bolt steering knuckle eye bracket.
Dimensional & Fitment Data
    • Chassis Application: Third-Generation Subaru Legacy Touring Wagon (BH5).
    • Axle Placement: Front Axle (side-specific asymmetrical left/right design).
    • Drive Configuration Compatibility: Symmetric All-Wheel Drive (AWD) / Front-Wheel Drive (FWD).
Part Numbers & Factory Cross-References
    • KYB (Excel-G Series) Aftermarket Numbers:
        • Right Hand (Front Driver's Side): 334273
        • Left Hand (Front Passenger's Side): 334274
    • Subaru Genuine OEM Numbers:
        • Right Hand: 20310AE100
        • Left Hand: 20310AE110

Subaru Impreza Drive Shafts

Original price was: KSh8,000.00.Current price is: KSh6,500.00.

Upgrade your drivetrain’s reliability and smoothness with these high-quality Drive Shafts for the Subaru Impreza. Sourced as genuine Ex-Japan parts, they are engineered to deliver efficient power transfer and eliminate vibrations, ensuring your Symmetrical All-Wheel Drive system performs at its peak.

PRICE: KSh 6,500

COMPATIBILITY: Precision-engineered for the Subaru Impreza series (GC, GD, GH, and GE models).

Subaru Legacy BP Rear Wheel Hub

Original price was: KSh9,000.00.Current price is: KSh8,000.00.

Upgrade your vehicle's handling and eliminate disruptive road noise with this high-durability Rear Wheel Hub for the Subaru Legacy BP. Sourced as a genuine Ex-Japan part, it is engineered to withstand the specific stresses of the Symmetrical All-Wheel Drive system, ensuring smooth rotation and maximum safety.

PRICE: KSh 8,000

COMPATIBILITY: Precision-engineered specifically for the Subaru Legacy BP series (2003–2009).

Subaru Forester SG5 Bilstein Shock Absorbers

Original price was: KSh8,000.00.Current price is: KSh7,000.00.

Upgrade your vehicle's handling and sport performance with these premium Bilstein Shock Absorbers for the Subaru Forester SG5. Sourced as genuine Ex-Japan parts, these pressurized gas shocks provide superior damping and stability, perfect for the driver who demands a firmer, more controlled ride.

PRICE: KSh 7,000

COMPATIBILITY: Precision-engineered for the Subaru Forester SG5 series (2002–2007).

Subaru Impreza Drive Shafts

Original price was: KSh7,500.00.Current price is: KSh6,500.00.

Upgrade your drivetrain’s reliability and smoothness with these high-quality Drive Shafts for the Subaru Impreza. Sourced as genuine Ex-Japan parts, they are engineered to deliver efficient power transfer and eliminate vibrations, ensuring your Symmetrical All-Wheel Drive system performs at its peak.

PRICE: KSh 6,500

COMPATIBILITY: Precision-engineered for the Subaru Impreza series (GC, GD, GH, and GE models).

Subaru Forester SH5 Complete Shock Absorbers

Original price was: KSh12,000.00.Current price is: KSh10,000.00.
Genuine Subaru Forester SH5 Complete Shocks for KSh 10,000. Grade A Ex-Japan quality including springs and mounts for superior AWD stability and ride height.
  • Price: KSh 10,000

  • Condition: Ex-Japan Grade A (Complete unit: Strut, Spring, and Top Mount)

  • Personality: "The All-Road Legend." Restores the perfect balance between highway comfort and off-road toughness.

  •  Compatibility: Grade A Ex-Japan complete strut assembly: Optimized for Subaru Forester SH5 (2.0X / 2.0XS) models (2008–2012).

Subaru Forester SJG Complete Shock Absorbers

Original price was: KSh12,000.00.Current price is: KSh10,000.00.
Genuine Subaru Forester SJG Complete Shocks for KSh 10,000. Grade A Ex-Japan quality for superior Symmetrical AWD handling, lift, and comfort.
  • Price: KSh 10,000

  • Condition: Ex-Japan Grade A (Complete unit: Strut, Spring, and Top Mount)

  • Personality: "The Turbocharged Guardian." Built for high-speed stability and heavy-duty SUV performance.

  • Grade A Ex-Japan complete strut assembly. Compatibility: Optimized for Subaru Forester SJG (2.0XT Turbo) and SJ5 models (2012–2018).

Subaru Legacy Drive Shafts (Model BR9)

Original price was: KSh13,000.00.Current price is: KSh12,000.00.

Upgrade your drivetrain’s reliability and smoothness with these high-quality Drive Shafts for the Subaru Legacy BR9. Sourced as genuine Ex-Japan parts, they are engineered to deliver efficient power transfer and eliminate vibrations, ensuring your All-Wheel Drive system performs at its peak.

PRICE: KSh 12,000

COMPATIBILITY: Precision-engineered specifically for the Subaru Legacy BR9 series (2009–2014).

Subaru Outback Rear Shock Absorbers

Original price was: KSh9,500.00.Current price is: KSh8,000.00.

Upgrade your vehicle's handling and comfort with these high-performance Rear Shock Absorbers designed for the Subaru Outback. Sourced as premium Ex-Japan parts, they are engineered to dampen road impact and stabilize your wagon, providing a smooth, controlled ride even when fully loaded.

PRICE: KSh 8,000

COMPATIBILITY: Precision-engineered for the Subaru Outback series (BP9/BPE and BR9 models).

Subaru Legacy BH5 Rear Wheel Hub

Original price was: KSh9,000.00.Current price is: KSh8,000.00.

Eliminate road noise and restore the smooth, stable handling of your Subaru Legacy BH5 with this high-durability Rear Wheel Hub. Engineered to withstand the specific stresses of All-Wheel Drive systems, it ensures your wheels rotate with zero friction and maximum safety.

PRICE: KSh 8,000

COMPATIBILITY: Precision-engineered specifically for the Subaru Legacy BH5 series (1998–2003).

Subaru Impreza Model 2018 Shock Absorbers

Original price was: KSh17,000.00.Current price is: KSh15,000.00.
Genuine 2018 Subaru Impreza Shocks for KSh 15,000. Ex-Japan Grade A quality for superior Symmetrical AWD handling and comfort.
  • Price: KSh 15,000

  • Condition: Ex-Japan Grade A (Certified low-mileage recovery)

  • Personality: The "Precision Navigator." Perfectly balanced for the driver who demands both comfort and cornering confidence

  • Compatibility: Fits Subaru Impreza (2017–2023) GT/GK Series (Fifth Generation), including 1.6i and 2.0i models.

Gemini said Subaru Forester SG5 Rear Shock Absorbers

Original price was: KSh9,500.00.Current price is: KSh8,000.00.

Restore the rugged performance and legendary stability of your Subaru Forester SG5 with these high-quality Rear Shock Absorbers. Engineered to eliminate sagging and absorb harsh road impacts, they ensure a smooth, level ride whether you are commuting in the city or exploring off-road trails.

PRICE: KSh 8,000

COMPATIBILITY: Precision-engineered specifically for the Subaru Forester SG5 series (2002–2008).

Gemini said Subaru Impreza Rear Shock Absorber (2007 Model)

Original price was: KSh11,000.00.Current price is: KSh10,000.00.

Restore the legendary handling and stability of your 2007 Subaru Impreza with this high-performance Rear Shock Absorber. Engineered to dampen road impacts and maintain tire-to-road contact, it provides a smooth, controlled ride and sharp cornering precision.

PRICE: KSh 10,000

COMPATIBILITY: Precision-engineered specifically for the 2007 Subaru Impreza (GD/GG series).

Subaru Forester SH5 Rear Wheel Hub Bearing

Original price was: KSh13,000.00.Current price is: KSh12,000.00.

Eliminate road noise and restore the legendary handling of your Subaru Forester SH5 with this premium Rear Wheel Hub Bearing. Engineered for high-speed stability and extreme durability, this unit ensures your wheels rotate smoothly and safely under all driving conditions.

PRICE: KSh 12,000

COMPATIBILITY: Precision-engineered specifically for the Subaru Forester SH5 model series.

Subaru Outback Rear Shocks

Original price was: KSh10,000.00.Current price is: KSh8,000.00.
High-quality Ex-Japan Grade A rear shock absorbers for Subaru Outback delivering comfort, control, and durability. Price: 8,000 Compatibility: Subaru Outback (BP/BL models), Compatible with select Subaru Legacy models Performance: Improved ride comfort,Better rear stability

Subaru BP5 Bilstain Shock Absorbers

Original price was: KSh10,000.00.Current price is: KSh8,000.00.
High-performance Ex-Japan Grade A Bilstein shock absorbers for Subaru Legacy BP5 delivering superior stability, comfort, and handling. Durable, reliable, and perfect for both daily and sporty driving. Price: 8,000

Compatibility: Subaru Legacy BP5, Subaru Outback BP series (confirm fitment before purchase

Performance Highlights: Improved road handling, Reduced body roll

SJG Subaru Forester Driveshafts

Original price was: KSh15,000.00.Current price is: KSh12,000.00.

SJG Subaru Forester Driveshafts

Price: 12,000

Condition: Ex-Japan – Grade A, lightly used and fully tested for smooth, reliable performance.
Compatibility: Specifically designed for Subaru Forester SJG ensuring precise OEM fit and seamless installation.
Performance: Delivers efficient power transfer to all wheels, reduces vibration, and enhances vehicle stability and handling.
Durability: Heavy-duty construction built to withstand turbo AWD performance and tough road conditions.
Value: Affordable at 12,000, offering dependable drivetrain performance and long-lasting reliability.

Subaru Forester Driveshafts Model SH5

Original price was: KSh15,000.00.Current price is: KSh12,000.00.

Subaru Forester SH5 Driveshafts

Price: 12,000

Condition: Ex-Japan – Grade A, lightly used and fully tested for reliability and smooth operation.
Compatibility: Specifically designed for Subaru Forester SH5 ensuring precise OEM fit and seamless installation.
Performance: Ensures smooth and efficient power transfer from the transmission to the wheels, reducing vibration and improving stability.
Durability: Heavy-duty construction built to withstand AWD stress and rough road conditions.
Value: Affordable at 12,000, delivering dependable performance and long-lasting drivetrain reliability.

Subaru Legacy Model br9 DriveShafts

Original price was: KSh15,000.00.Current price is: KSh12,000.00.

Subaru Legacy BR9 Driveshafts

 Price: 6500

Condition: Ex-Japan – Grade A, lightly used, fully tested for reliability and smooth operation.
Compatibility: Specifically designed for Subaru Legacy BR9 ensuring precise OEM fit and seamless installation.
Performance: Provides smooth and efficient power transfer from the transmission to the wheels, reducing vibrations and enhancing vehicle stability.
Durability: Built with high-quality materials to withstand drivetrain stress and long-term use.
Value: Affordable at 6500, delivering reliable performance and stability for daily and highway driving.

Subaru Legacy Driveshafts

Original price was: KSh7,900.00.Current price is: KSh6,500.00.

Subaru Legacy Driveshafts 

Price: 6500

Condition: Ex-Japan – Grade A, lightly used, fully tested for reliability and smooth performance.
Compatibility: Perfectly engineered for Subaru Legacy, ensuring precise OEM fit and seamless installation.
Performance: Efficiently transfers engine power to the wheels, providing smooth acceleration, stable handling, and optimal drivetrain performance. Reduces vibrations and enhances control.
Durability: Built with premium materials to withstand stress, wear, and harsh driving conditions.
Value: Affordable at 6500, delivering dependable performance, stability, and long-lasting reliability for daily driving or spirited performance.

Showing 28 of 56 results
Please select your product
Product has been added to your cart
Compare (0)