Hilux Vigo 4WD Driveshafts

(0 Reviews) Write a review
Front CV Drive Shafts (Left & Right Axis)

The front independent front suspension (IFS) uses complete outer CV joint driveshafts with the following physical specifications depending on the exact production month: [1, 2]
  • Spline Count (Wheel/Outer Side): 30 splines
  • Spline Count (Differential/Inner Side): 30 splines
  • Total Component Length (Variant A – Up to 05/2012): 630 mm
  • Total Component Length (Variant B – 05/2012 to 2015): 632 mm
  • Hub Retaining Nut Thread Size: M28 x 1.5
  • Hub/CV Shaft Axle Nut Torque Spec: 235 Nm (173 ft-lb)
  • OEM Reference Numbers: 43430-0K020, 43430-0K030, 43430-0K050, 43430-0K021, 43430-0K022, 43430-0K051, 43430-0K023 [1, 2]
Rear Propeller Shaft (Tail Shaft) & Center Bearing

The longitudinal rear driveshaft delivering power from the transfer case to the rear differential contains the center support bearing assembly and standard universal joints: [1, 2]
  • Driveshaft Flange Nut Torque Spec: 88 Nm (65 ft-lb)
  • Center Bearing Staked Nut Size: 24 mm socket profile
  • Center Bearing Nut Torque Spec: 181 Nm initial, then loosen and final retorque to 82 Nm
  • Transmission Compatibility: Specific models segmented strictly by manual transmission (MT) vs. automatic transmission (AT) layout lengths.

    [1, 2]

KSh18,000.00

In stock
Buy now

Description

1. Front Axle Driveshafts (Left & Right Front CV Axles)

These are the half-shafts that transmit power from the front differential outward to the front wheel hubs.

  • Function: Transfer rotational power under varying steering angles and suspension travel.

  • Design/Components:

    • Outer CV Joint (Wheel Side): A constant velocity joint covered by a rubber boot (packed with high-temperature grease) allowing the wheels to turn left or right seamlessly.

    • Inner CV Joint (Differential Side): Plunge-type joint that allows the driveshaft to lengthen and shorten as the front suspension compresses and rebounds.

  • Common Specifications:

    • Spline Count: Typically features a 30-tooth outer spline configuration (depending on exact engine size like the 2.5L 2KD-FTV or 3.0L 1KD-FTV).

    • Material: High-strength chromoly or carbon steel tubing designed to handle heavy torque loads in 4WD mode.

2. Propeller Shafts (Front & Rear Cardan Shafts)

In a 4WD Hilux Vigo, the “propshafts” connect the transfer case to the front and rear differentials.

  • Front Propeller Shaft:

    • Runs from the transfer case to the front differential.

    • Shorter and lighter duty, it only spins under load when 4WD is engaged (on part-time 4WD systems).

  • Rear Propeller Shaft:

    • Runs from the transmission/transfer case to the rear differential.

    • Usually a two-piece design supported by a center support bearing (carrier bearing) to mitigate vibration over the longer wheelbase.

  • Design/Components:

    • Universal Joints (U-Joints/Spiders): Allow flexibility and angle adjustment as the axle moves up and down relative to the chassis.

    • Slip Yoke: Allows the shaft to telescope slightly to accommodate changes in distance between the transmission and the rear axle during suspension movement.

Quick Overview Table

Component Type Location Primary Role Key Wear Items
Front CV Driveshafts Between Front Diff & Front Wheels Steerable power delivery to front wheels CV boots (tears lead to joint failure), internal joint wear
Front Propeller Shaft Between Transfer Case & Front Diff Transmits 4WD power to front axle U-joints, sliding splines
Rear Propeller Shaft Between Transfer Case & Rear Diff Main drive line pushing the vehicle Center support bearing, U-joints, balancing weights

Reviews

There are no reviews yet.

Be the first to review “Hilux Vigo 4WD Driveshafts”

Your email address will not be published. Required fields are marked *

Please select your product
Product has been added to your cart
Compare (0)