Sort

Suzuki Alto Model 2015 Rear Shock

KSh3,500.00
1. Damping Architecture & Performance Mechanics
  • System Design Type: Gas-Pressurized Telescopic Hydraulic Damper
  • Damping Design: Twin-tube double-acting low-pressure hydraulic system
  • Fitting Position: Rear Axle (Symmetric construction; Left-Hand and Right-Hand units are mechanically interchangeable)
  • Functional Intent: Controls vehicle pitch and eliminates high tire bounce on ultra-light chassis profiles (sub-700 kg vehicle curb weight)
2. Mounting Configuration & Structural Connections
  • Upper Mounting Connection: Stem / Pin top end featuring a threaded stud assembly complete with two vulcanized rubber isolation cushions, retaining washers, and locking nuts.
  • Lower Mounting Connection: Closed metal eyelet ring containing a factory pre-pressed steel-sleeved horizontal natural rubber bushing.
  • Chassis Series Compatibility: HA36S, HA36V (Fits standard 2WD and 4WD configurations, though valving rates vary slightly between drivetrain packages)
3. Genuine OEM & Aftermarket Part Numbers
  • Genuine Suzuki OEM Part Numbers: 41800-74P00, 41800-74P10, 41800-74P01
  • Aftermarket Cross-References: KYB Excel-G / Gas-A-Just Series (Part Numbers: 3420011 / 3430013 depending on specific suspension travel calibration)
4. Metallurgical & Component Composition
  • Piston Rod Build: Induction-hardened carbon steel rod core finished with an anti-friction, mirror-smooth hard chrome plating layer to extend oil seal lifespan.
  • Gas Media: Low-pressure Nitrogen gas (N₂) injection to continuously suppress hydraulic oil foaming, aeration, and thermal fade under continuous travel cycles.
  • Fluid Seal: High-integrity multi-lip synthetic nitrile rubber pressure seal paired with an integrated external dust/grit wiper ring.
  • Surface Coating: Finished with an anti-corrosion black electrophoresis paint layer to shield the damper outer tube from road debris, moisture, and rust.

Toyota Passo Rear Shocks

KSh2,500.00
1. Damping Architecture & Performance Mechanics
  • System Design Type: Gas-Pressurized Telescopic Hydraulic Damper
  • Damping Technology: Twin-Tube double-acting low-pressure design
  • Fitting Position: Rear Axle (Symmetric construction; Left-Hand and Right-Hand units are mechanically interchangeable)
  • Functional Intent: Suppresses vehicle pitch, stabilizes lateral body roll, and eliminates high wheel bouncing under varying payload thresholds.
  • Standard Service Lifespan: Approximately 60,000 to 100,000 km (Recommended inspection cycles every 10,000 to 20,000 km). [1]
2. Mounting Matrix & Physical Dimensions
  • Upper Mounting Connection: Pin/Stem top end featuring a threaded stud assembly complete with two vulcanized rubber isolation cushions and locking washers. [1]
  • Lower Mounting Connection: Rigid eyelet ring containing a pre-pressed steel-sleeved horizontal natural rubber bushing linked by a metric M12 structural union bolt. [1]
  • Stroke Action Profile: Short-travel piston calibration custom-valved for sub-1,000 kg compact hatchback kerb weights.
3. Part Number Profiles By Vehicle Generation
3rd Generation (M700 / M710 Series: 2016–2023) [1]
  • Genuine OEM Reference: 48530B9275 (Marked body tag: 48531-B1250)
  • 4WD Specific OEM Reference: 48530B9160
  • Aftermarket Cross-Reference: KYB Gas Damper Series Part Number 343406 [1, 2]
2nd Generation (KGC30 / NGC30 Series: 2010–2016) [1]
  • Genuine OEM Reference: 48531-B1070, 48531-B1090
  • Aftermarket Cross-Reference: KYB Excel-G Series Part Number 343447 [1]
1st Generation (KGC10 / QNC10 Series: 2004–2010) [1]
  • Genuine OEM Reference: 48531-B1010, 48531-B1011, 48531-B1012, 48531-B1040
  • Aftermarket Cross-Reference: KYB Part Number 343406 [1, 2, 3]
4. Metallurgical & Component Specs
  • Piston Rod Engineering: High-tensile carbon steel rod core, induction-hardened and coated with a mirror-smooth micro-grooved chrome finish to eliminate seal drag.
  • Working Charge Media: Low-pressure Nitrogen gas (N₂) configuration to prevent hydraulic fluid cavitation, foaming, and high thermal fade during rapid cycles. [1]
  • Fluid Seal: High-durability multi-lip synthetic nitrile rubber seal accompanied by an integrated external debris scraper edge to restrict entry of environmental grit. [1]

Honda Fit Engine Mount

KSh3,500.00
1. Honda Fit 3rd Generation (GK3 / GK5 Chassis: 2014–2020)
This generation utilizes a refined torque-rod setup to stabilize engine pitch under rapid acceleration and braking.
  • Right Side Mount (Engine / Timing Chain Side):
    • Design Architecture: Hydraulic / Liquid-Filled Mount with integrated aluminum frame housing.
    • Genuine OEM Part Numbers: 50822-T5R-A01, 50822-T5A-J01
    • Aftermarket Cross-References: Febest (HM-GKRH)
  • Left Side Mount (Transmission / Gearbox Side):
    • Design Architecture: Solid vulcanized natural rubber isolator bracket.
    • Genuine OEM Part Numbers: 50850-T5R-A01, 50850-T5A-911 (CVT specific variants)
    • Aftermarket Cross-References: Febest (HM-GKLH)
  • Rear Lower Mount (Torque Strut / Dog Bone):
    • Design Architecture: Hard rubber dual-bushing anti-torque link rod. Controls backward and forward engine block roll.
    • Genuine OEM Part Numbers: 50890-T5A-911, 50890-T5R-A01
    • Aftermarket Cross-References: Febest (HM-GKR)

2. Honda Fit 2nd Generation (GE6 / GE8 Chassis: 2008–2013)
One of the most common configurations in the market, relying heavily on a large fluid-filled upper right mount.
  • Right Side Mount (Engine / Timing Chain Side):
    • Design Architecture: Premium Hydraulic (Liquid-Filled) core inside a cast-iron/aluminum retaining collar.
    • Genuine OEM Part Numbers: 50822-TF0-J02, 50822-TG0-T02, 50822-TF0-305
    • Aftermarket Cross-References: RBI (O10208RE), Febest (HM-GERH)
  • Left Side Mount (Transmission Upper Mount):
    • Design Architecture: Solid natural rubber dampening cushion bracket assembly.
    • Genuine OEM Part Numbers: 50850-TF0-981, 50850-TF0-J11
    • Aftermarket Cross-References: RBI (O10408LH), Febest (HM-GELH)
  • Rear Lower Mount (Transmission Rear Rod):
    • Design Architecture: Structural rubber damper sleeve link.
    • Genuine OEM Part Numbers: 50890-TF0-911, 50890-TF0-981
    • Aftermarket Cross-References: RBI (O10508R), Febest (HM-GER)

Material & Metallurgical Composition (All Generations)
  • Rubber Polymer Matrix: High-tensile Natural Rubber (NR) blend calibrated to 60–65 Shore A durometer hardness to resist tearing under high shear torque.
  • Hydraulic Fluid Core: Internal chambers packed with low-viscosity glycol-based fluid designed to absorb low-frequency engine resonance at idle speeds.
  • Structural Brackets: Finished with an anti-corrosion black powder coat or zinc-galvanized plating to shield structural steel plates from humidity and rust.

Harrier 240 Engine Mountains

KSh4,000.00
1. Front Engine Mount (Radiator Side)
  • Design Architecture: Active Vacuum-Controlled Hydraulic Mount (Liquid-Filled)
  • Functional Mechanics: Features an internal fluid chamber connected to an engine vacuum line. The internal valve dynamically switches stiffness to dampen engine vibrations at idle speed and firms up under load.
  • Genuine OEM Part Numbers: 12361-28110, 12361-28220
  • Aftermarket Cross-References: RBI (T09A03F), Febest (TM-MCU30F)
2. Rear Engine Mount (Firewall Side)
  • Design Architecture: Heavy-Duty Hydraulic Mount (Liquid-Filled)
  • Functional Mechanics: A passive multi-chamber hydraulic isolator that counteracts structural engine block rotation and torque pullback during acceleration and braking.
  • Genuine OEM Part Numbers: 12371-28060, 12371-28240
  • Aftermarket Cross-References: RBI (T09A03R), Febest (TM-ACU30R)
3. Right Engine Mount (Timing Belt / Engine Pulley Side)
  • Design Architecture: Solid Vulcanized Natural Rubber with Integrated Aluminum Bracket
  • Functional Mechanics: Serves as the primary weight-bearing structural mount supporting the engine block to the inner body frame rail.
  • Genuine OEM Part Numbers: 12305-28120, 12305-28130, 12305-28230
  • Aftermarket Cross-References: RBI (T09A03RH), Febest (TM-ACU30RH)
4. Left Engine Mount (Gearbox / Transmission Side)
  • Design Architecture: Solid Rubber Core / Anchor Bracket Design
  • Functional Mechanics: Supports the weight of the automatic transaxle housing and manages horizontal transmission shift load shifts.
  • Genuine OEM Part Numbers: 12372-28020, 12372-28200
  • Aftermarket Cross-References: RBI (T09A03LH), Febest (TM-ACU30LH)
Material & Metallurgical Composition
  • Rubber Element: Premium Natural Rubber (NR) compound featuring a 55–65 Shore A durometer rating for balance between structural durability and resonance dampening.
  • Metal Casting: High-pressure die-cast aluminum alloy bracket bodies paired with stamped structural carbon steel base plates.
  • Surface Coating: All steel components are treated with a black anti-corrosion phosphate or electrophoresis layer to prevent moisture rust degradation.

Mazda 3 Front Shock

KSh12,500.00
1. Mazda 3 4th Generation (BP Series: 2019–Present)
Engineered for the SkyActiv-Vehicle Architecture to enhance linear handling and tire-to-road contact profiles.
  • Suspension Architecture: MacPherson Strut Assembly with an integrated coil spring tower perch
  • Damping Design: Twin-tube gas-pressurized hydraulic system
  • Fitting Position: Front Axle (Asymmetric Left-Hand and Right-Hand specific units)
  • Chassis Series Compatibility: BP5P, BP8P, BPEK, BPFP (2WD & AWD models)
  • Genuine OEM Part Numbers:
    • Right Hand (RH): BCKA-34-700, BCKA-34-700A, BDGH-34-700
    • Left Hand (LH): BCKA-34-900, BCKA-34-900A, BDGH-34-900
  • Aftermarket Cross-References: KYB Excel-G Series (Part Numbers: 3340182 for RH / 3340183 for LH)

2. Mazda 3 3rd Generation (BM/BN Series: 2014–2018)
Optimized for traditional SkyActiv-Chassis ride dynamics, balancing sportiness with road vibration isolation.
  • Suspension Architecture: MacPherson Strut Assembly with top-mount bearing integration
  • Damping Design: Gas-charged double-acting hydraulic pressure system
  • Fitting Position: Front Axle (Asymmetric Left-Hand and Right-Hand specific units)
  • Chassis Series Compatibility: BM5FS, BM5AS, BMEFS, BM2FS, BYEFP
  • Genuine OEM Part Numbers:
    • Right Hand (RH): B45A-34-700, B45A-34-700A, B62G-34-700
    • Left Hand (LH): B45A-34-900, B45A-34-900A, B62G-34-900
  • Aftermarket Cross-References: KYB Excel-G Series (Part Numbers: 3340114 for RH / 3340115 for LH)

Material & Structural Blueprint (All Generations)
  • Piston Rod Architecture: Induction-hardened, high-tensile carbon steel finished with an anti-friction, micro-smooth hard chrome plating layer to extend oil seal lifespan.
  • Working Gas Media: Low-pressure Nitrogen gas (N₂) injection to continuously suppress hydraulic oil foaming, aeration, and thermal fade under load cycles.
  • Valving Control: Multi-stage, velocity-sensitive internal valving matrix that scales hydraulic resistance automatically relative to piston stroke speed.
  • Fluid Seals: Multi-lip synthetic rubber oil pressure seal combined with an external abrasive dirt-scraper ring.

Mazda CX5 Diesel Engine

KSh450,000.00
1. Engine Block & Core Architecture
  • Engine Code: SH-VPTS / SH-VPTR
  • Engine Type: SkyActiv-D, Water-cooled Inline 4-Cylinder, 16-Valve DOHC
  • Aspiration: Two-stage twin turbocharger (one small, one large turbo operating sequentially) with integrated intercooler
  • Displacement: 2,191 cc (2.2 Liters)
  • Bore x Stroke: 86.0 mm × 94.3 mm
  • Compression Ratio: 14.0:1 (Uniquely low for a diesel engine, reducing peak combustion temperatures and pressures to allow a lightweight aluminum block design)
  • Fuel System: Common-Rail Direct Injection with piezo-electric multi-hole injectors
2. Performance & Torque Outputs
  • Standard Output Variant (2012–2017 models):
    • Maximum Power: 150 PS / 175 PS (110 kW / 129 kW) @ 4,500 RPM
    • Maximum Torque: 380 Nm / 420 Nm @ 2,000 RPM
  • High-Output Upgraded Variant (2018–Present models):
    • Maximum Power: 184 PS / 200 PS (135 kW / 147 kW) @ 4,000 RPM
    • Maximum Torque: 450 Nm @ 2,000 RPM
  • Valvetrain: Chain-driven DOHC with VVL (Variable Valve Lift) on the exhaust side to facilitate internal exhaust gas recirculation for faster warm-ups and emission control.
3. Service Fluid & Maintenance Specifications
  • Recommended Engine Oil: SAE 0W-30 or SAE 5W-30 meeting ACEA C3 / JASO DL-1 specifications (Low-SAPS/Low-Ash oil is strictly mandatory to prevent clogging the Diesel Particulate Filter).
  • Engine Oil Capacity:
    • 5.6 Liters (with oil filter replacement)
    • 5.1 Liters (service refill without filter)
  • Coolant System Capacity: ~8.2 to 8.6 Liters (Mazda FL22 long-life coolant)
  • Emission Control Suite: Diesel Particulate Filter (DPF), Exhaust Gas Recirculation (EGR), and Selective Catalytic Reduction (SCR / AdBlue) on later European/global face-lift models.
  • Firing Order: 1 - 3 - 4 - 2

Noah Slim Engine

KSh110,000.00
1. 1.8L Hybrid Slim Engine (2ZR-FXE)
This powertrain powers the hybrid variants of the Toyota Noah (ZWR80 / ZWR90 series) and is optimized for low thermal loss and maximum space efficiency.
  • Engine Configuration: Inline 4-Cylinder, 16-Valve DOHC, Atkinson Cycle
  • Displacement: 1,798 cc (1.8 Liters)
  • Bore x Stroke: 80.5 mm × 88.3 mm
  • Compression Ratio: 13.0:1 (High-expansion ratio)
  • Valvetrain Integration: Dual VVT-i (Variable Valve Timing with intelligence)
  • Maximum Power (Engine Only): 99 PS (73 kW) @ 5,200 RPM
  • Maximum Torque (Engine Only): 142 Nm @ 4,000 RPM
  • Engine Architecture: Beltless engine block structure utilizing a fully electric water pump and electronic air conditioning compressor to save physical space.
2. 2.0L Valvematic Slim Engine (3ZR-FAE)
This engine powers the mainstream third-generation petrol variants (ZRR80 series) before the platform shifted to the Dynamic Force engines.
  • Engine Configuration: Inline 4-Cylinder, 16-Valve DOHC, Otto Cycle
  • Displacement: 1,986 cc (2.0 Liters)
  • Bore x Stroke: 80.5 mm × 97.6 mm
  • Compression Ratio: 10.0:1
  • Valvetrain Integration: Dual VVT-i with Valvematic technology (continuously variable valve lift mechanisms that reduce pumping loss and trim fuel intake requirements)
  • Maximum Power: 152 PS (112 kW) @ 6,100 RPM
  • Maximum Torque: 193 Nm @ 3,800 RPM
3. Maintenance & Fluid Specs
  • Recommended Engine Oil Weight: SAE 0W-20 (highly recommended for tight bearing tolerances) or SAE 5W-30
  • Oil Sump Capacity: 4.2 Liters (with oil filter replacement)
  • Spark Plug Specifications: Iridium-tipped long-reach spark plugs (e.g., DENSO SC20HR11 or equivalent)
  • Coolant System Capacity: ~5.8 to 6.3 Liters (Toyota Super Long Life Coolant)
  • Camshaft Drive: Maintenance-free, high-strength timing chain system

2ZR Slim Engine

KSh110,000.00
1. Core Engine Dimensions & Architecture
  • Engine Type: Water-cooled Inline 4-Cylinder, 16-Valve DOHC
  • Displacement: 1,798 cc (1.8 Liters)
  • Bore x Stroke: 80.5 mm × 88.3 mm (3.17 in × 3.48 in)
  • Cylinder Block Material: Die-cast Aluminum alloy with spiny-type cast iron cylinder liners
  • Cylinder Head Material: Aluminum alloy
  • Valvetrain Drive: Chain-driven roller rocker arms with hydraulic lash adjusters (no manual valve shim maintenance needed)
  • Engine Weight (Dry): ~117 kg to 124 kg depending on the specific accessory configuration [1, 2, 3, 4, 5, 6]
2. Performance Outputs By Variant
Base Variant: 2ZR-FE (Standard Dual VVT-i)
  • Compression Ratio: 10.0:1
  • Maximum Power Output: 132 – 140 hp (98 – 103 kW) @ 6,000 RPM
  • Maximum Torque: 173 – 177 Nm @ 4,000 – 4,400 RPM
  • Fuel System: Multi-point Electronic Fuel Injection (EFI) [1, 2, 3]
Premium Variant: 2ZR-FAE (Valvematic Tech - "Slim Valvmatic")
  • Compression Ratio: 10.5:1
  • Maximum Power Output: 139 – 148 hp (104 – 110 kW) @ 6,200 – 6,600 RPM
  • Maximum Torque: 171 – 180 Nm @ 4,000 RPM
  • Tech Enhancements: Adds continuously variable valve lift adjustment (Valvematic), bypassing throttle valve restrictions to yield a 5% to 10% gain in fuel economy. [1, 2, 3]
Hybrid Variant: 2ZR-FXE (Atkinson Cycle)
  • Compression Ratio: 13.0:1
  • Maximum Power Output (Engine Only): 98 hp (73 kW) @ 5,200 RPM
  • Maximum Torque: 142 Nm @ 4,000 RPM
  • Tech Enhancements: High-expansion ratio Atkinson cycle, belt-less engine operation utilizing an electric water pump. [1]
3. Service Fluid & Tune-up Specifications
  • Recommended Engine Oil Weight: SAE 0W-20 (preferred) or SAE 5W-30 (API SN / ILSAC GF-5 or higher) [1, 2]
  • Engine Oil Capacity:
    • 4.2 Liters (with oil filter replaced)
    • 3.9 Liters (dry engine refill / without filter) [1]
  • Coolant System Capacity: ~5.5 to 6.5 Liters (Toyota Super Long Life Coolant)
  • Spark Plug Type: Iridium-tipped long-reach plugs (e.g., DENSO SC20HR11)
  • Firing Order: 1 - 3 - 4 - 2 [1]

Mazda Demio ZDJ20 Slim Engine

KSh40,000.00
1. Engine Core & Block Architecture
  • Engine Code: S5-DPTS / S5-DPTR
  • Engine Type: SkyActiv-D, Water-cooled Inline 4-Cylinder, DOHC 16-Valve
  • Aspiration: Variable Geometry Turbocharger (VGT) with integrated water-cooled intercooler
  • Displacement: 1,498 cc (1.5 Liters)
  • Bore x Stroke: 76.0 mm × 82.6 mm
  • Compression Ratio: 14.8:1 (Uniquely low compression ratio for a diesel engine, minimizing internal structural strain and allowing a lightweight, slim engine casting)
  • Fuel System: Common-Rail Direct Injection (Solenoid injectors enabling ultra-fine multi-stage fuel misting) [1, 2]
2. Performance Outputs
  • Maximum Power Output: 105 PS (77 kW / 104 HP) @ 4,000 RPM
  • Maximum Torque (6-Speed Automatic variant): 250 Nm (25.5 kg-m) @ 1,500 – 2,500 RPM
  • Maximum Torque (6-Speed Manual variant): 220 Nm (22.4 kg-m) @ 1,400 – 3,200 RPM
  • Power-to-Weight Efficiency: Optimized to drive front-wheel (FF) layouts weighing approximately 1,080 kg to 1,130 kg. [1, 2]
3. Drivetrain & Fluid Capacities
  • Transmission Matches: 6-speed SKYACTIV-Drive Automatic (AWD / FF configurations) or 6-speed SKYACTIV-MT Manual
  • Fuel Tank Capacity: 44 Liters
  • Recommended Engine Oil: SkyActiv-D 0W-20 or 5W-30 DL-1 (Low Ash/SAPS mandatory specification for DPF maintenance)
  • Emission Control System: Diesel Particulate Filter (DPF) setup with a maintenance-free NOx storage catalyst (removes the need for AdBlue/urea fluid additives)

Suzuki Alto Model 2017 Wheel Hub Bearing

KSh4,500.00
Front Wheel Hub Bearing Specifications
  • Bearing Design Architecture: Double-row angular contact ball bearing (Generation 1 cartridge style). [1]
  • Dimensions & Fitment Matrix:
    • Inner Diameter (d): 35.00 mm
    • Outer Diameter (D): 62.00 mm
    • Total Width (W): 40.00 mm [1, 2]
  • Braking Dynamics Integration: Fits models with or without Anti-lock Braking System (ABS) dependent on regional trim variants. [1, 2]
  • Genuine OEM Part Numbers: 43440-58J00, 43401-64L00 (Hub Set), 43401-74P00. [1, 2, 3]
  • Aftermarket Cross-References: SKF (VKBA 3965), SWAG (84 93 1342), SO.HQ 43401-64L00 Set. [1, 2, 3]
Rear Wheel Hub Bearing Specifications
  • Bearing Design Architecture: Single-row or integrated double-row tapered/ball configurations depending on 2WD vs. 4WD layouts. [1, 2]
  • Dimensions & Fitment Matrix (Standard 2WD):
    • Inner Diameter: 25.00 mm
    • Outer Diameter: 52.00 mm
    • Total Width: 42.00 mm [1]
  • Genuine OEM Part Numbers: PW25520042CS. [1]
  • Aftermarket Cross-References: RIDEX (654W0474), FEBI BILSTEIN (31341). [1]
Material & Metallurgical Composition
  • Core Material Element: High-cleanliness, induction-hardened chromium steel (Gcr15 structural grade) ensuring wear thresholds against load cycles. [1]
  • Internal Seal Matrix: Nitrile butadiene rubber (NBR) multi-lip dual-shield system preventing abrasive dirt intrusion and moisture breakdown. [1]
  • Lubrication Element: Factory-packed with premium lithium-complex high-temperature grease.

Toyota Vanguard Front Shock Absorber

KSh3,000.00
Geometrical & Architecture Specifications
  • Suspension System: MacPherson Strut Assembly with integrated spring seat tower.
  • Internal Valve Construction: Twin-tube low-pressure design optimized for SUV ride stability and cabin comfort.
  • Fitting Position: Front Axle (Asymmetric Left-Hand and Right-Hand specific units; not interchangeable).
  • Chassis Compatibility: Interchangeable across ACA33W, ACA38W, GSA33W configurations (240S, 350S, 2WD, and 4WD variants).
  • Knuckle Attachment Mount: Heavy-duty double-bolt steering knuckle mounting bracket welded to the lower strut casing.
  • Sway Bar Link: Integrated stabilizer bracket on the outer shell body for direct stabilizer link attachment. [1, 2, 3, 4, 5]
Genuine OEM & Aftermarket Cross-Reference Part Numbers
  • Right Hand (RH - Front Strut Assembly):
    • Toyota Genuine OEM: 48510-80366, 48510-42190
    • Aftermarket Identifiers: KYB Excel-G Series Part Number 339031 [1, 2, 3]
  • Left Hand (LH - Front Strut Assembly):
    • Toyota Genuine OEM: 48520-80130, 48520-42190
    • Aftermarket Identifiers: KYB Excel-G Series Part Number 339032 [1, 2, 3]
Core Material & Structural Specs
  • Piston Rod Build: Heavy-duty, high-tensile carbon steel finished with an anti-wear micro-smooth hard chrome plating layer to extend oil seal lifespan.
  • Dampening Element: Multi-stage, velocity-sensitive internal valving matrix that scales hydraulic resistance automatically relative to piston stroke speed.
  • Gas Media: Low-pressure Nitrogen gas (N₂) injection to continuously suppress hydraulic oil foaming, aeration, and thermal fade under continuous heavy load cycles.
  • Fluid Seal: High-integrity multi-lip synthetic rubber seal complete with an integrated external dirt/abrasive scraper ring.

Toyota Rav4 Shock Absorber

KSh3,000.00
1. Toyota RAV4 5th Generation (XA50 Series: 2019–Present)
Engineered for the TNGA-K (Toyota New Global Architecture) platform to deliver a lower center of gravity and sharper handling.
Front Strut Specifications
  • System Type: Gas-Pressurized MacPherson Strut Assembly
  • Internal Design: Twin-tube with high-speed sensitive valving
  • Fitting Position: Front Axle (Asymmetric Left and Right specific units)
  • Chassis Series: MXAA52, MXAA54, AXAH52, AXAH54 (2WD / AWD / Hybrid)
  • Genuine OEM Part Numbers:
    • Right Hand (RH): 48510-80927, 48510-42350, 48510-42370
    • Left Hand (LH): 48520-80645, 48520-42350, 48520-42370
  • Aftermarket Equivalents: KYB Excel-G Series (3340206 for RH / 3340207 for LH)
Rear Shock Specifications
  • System Type: Gas-Charged Telescopic Hydraulic Damper
  • Suspension Layout: Multi-link trailing arm rear suspension setup
  • Fitting Position: Rear Axle (Symmetric / interchangeable Left and Right)
  • Genuine OEM Part Numbers: 48530-42170, 48530-80784, 48530-42210
  • Aftermarket Equivalents: KYB Excel-G Series (3440058)

2. Toyota RAV4 4th Generation (XA40 Series: 2013–2018)
Built for standard highway comfort and light off-road stability on the traditional RAV4 platform.
Front Strut Specifications
  • System Type: Oil/Gas-Pressurized MacPherson Strut Assembly
  • Internal Design: Twin-tube low-pressure design
  • Fitting Position: Front Axle (Asymmetric Left and Right specific units)
  • Chassis Series: ZASA42, ZASA44, ASA42, ASA44, AVA42, AVA44
  • Genuine OEM Part Numbers:
    • Right Hand (RH): 48510-42230, 48510-80648, 48510-42260
    • Left Hand (LH): 48520-42230, 48520-80388, 48520-42260
  • Aftermarket Equivalents: KYB Excel-G Series (339275 for RH / 339276 for LH)
Rear Shock Specifications
  • System Type: Gas Pressure Double-Acting Hydraulic Damper
  • Fitting Position: Rear Axle (Symmetric / interchangeable Left and Right)
  • Mounting Configuration: Top eyelet pin bush with reinforced lower rubber bushing ring
  • Genuine OEM Part Numbers: 48530-42110, 48530-42130, 48530-80689
  • Aftermarket Equivalents: KYB Excel-G Series (349140)

Core Structural & Material Specifications (All Generations)
  • Piston Rod Build: Micro-grooved, induction-hardened carbon steel with hard-chrome mirror finishing to drop seal friction limits.
  • Working Gas Media: Low-pressure Nitrogen gas (N₂) injection to permanently suppress hydraulic fluid cavitation, foaming, and performance fading under heat cycles.
  • Seal System: Multi-lip synthetic rubber oil pressure seal combined with an external abrasive dirt-scraper ring.
  • Valving Matrix: Multi-stage, velocity-sensitive rebound and compression discs that adjust hydraulic flow dynamically relative to piston stroke speed.

Toyota Passo Model 2018 Shock Absorber

KSh6,000.00
Front Shock Absorber (Strut) Specifications
    • System Type: Gas/Oil-Pressurized MacPherson Strut Assembly
    • Damping Design: Twin-tube internal hydraulic architecture
    • Fitting Position: Front Axle (Asymmetric left and right specific layout)
    • Chassis Series: M700A (2WD / Front-Wheel Drive), M710A (4WD variant)
    • Aftermarket Cross-Reference: KYB Excel-G Series (Part Number: 332120) [1, 2, 3, 4, 5]
Rear Shock Absorber Specifications
    • System Type: Gas-Charged Telescopic Hydraulic Damper [1]
    • Damping Design: Twin-tube double-acting pressure system
    • Fitting Position: Rear Axle (Symmetric / interchangeable left and right)
    • Mounting Configuration: Top stem pin/eyelet joint with a reinforced lower rubber eyelet bushing [1, 2]
    • Genuine OEM Part Numbers:
        • 2WD Models: 48530B9275 (Marked: 48531-B1250)
        • 4WD Models: 48530B9160 [1, 2]
    • Aftermarket Cross-Reference: KYB Gas Damper Series (Part Number: 343406) [1]
Material & Structural Specs
  • Piston Rod Construction: High-tensile, induction-hardened steel finished with an anti-friction, micro-smooth hard chrome plating. [1]
  • Gas Element: Low-pressure Nitrogen gas (N₂) injection to actively suppress hydraulic oil aeration, cavitation, and heat-induced damping fade.
  • Oil Seal Design: High-integrity multi-lip synthetic rubber seal integrated with a secondary external dirt-wiper ring. [1]
  • Valving Mechanism: Velocity-sensitive, multi-stage rebound disc matrix that scales damping resistance relative to road-induced piston velocity.

Nissan Note E11 Lower Arm Control

KSh3,500.00
Structural & Geometrical Specifications
  • Suspension Architecture: Front Axle Lower Wishbone / A-Arm assembly designed for MacPherson strut configurations.
  • Component Symmetry: Asymmetric design (Left-Hand and Right-Hand units are distinct and not interchangeable).
  • Material Matrix: Stamped high-tensile sheet steel with robotically welded structural reinforcements.
  • Surface Finish: Electrophoresis anti-rust black coating for corrosion resistance.
  • Component Weight: Approximately 2.3 kg to 2.5 kg per individual arm assembly (including pre-pressed bushings and ball joint).
  • Chassis Compatibility: Interchangeable across the Nissan B-platform including the Note E11, Tiida C11, Micra/March K12, and Cube Z11.
Integrated Hardware & Connection Specs
  • Ball Joint Configuration: Integrated press-fit lower ball joint with a heavy-duty rubber dust boot and grease retention clip.
  • Ball Joint Stud Pin Diameter: Standard Ø 18 mm tapered fitment.
  • Bushing Layout (Dual Silent-Block System):
    • Front Inner Bushing: Horizontal cylindrical steel-sleeved natural rubber bushing.
    • Rear Inner Bushing: Large vertical lip/flange-type bushing engineered to isolate cabin floor vibration.
    • Rubber Hardness: 60–65 Shore A durometer optimized for structural rigidity under braking and steering loads.
Genuine OEM & Aftermarket Part Numbers
  • Right Hand (RH - Front Lower Arm):
    • Nissan Genuine OEM: 54500-AX600, 54500-AX00A, 54500-9U00A, 54500-BC40A, 54500-ED00A
    • Aftermarket Identifiers: Febest (0224-K12RH), Blue Print (ADN186117), Delphi (TC1374)
  • Left Hand (LH - Front Lower Arm):
    • Nissan Genuine OEM: 54501-AX600, 54501-AX00A, 54501-9U00A, 54501-BC40A, 54501-ED00A
    • Aftermarket Identifiers: Febest (0224-K12LH), Blue Print (ADN186116), Delphi (TC1373)

Nissan Tiida Lower Arm Control

KSh3,500.00
Structural & Geometrical Specifications
  • Suspension Type: Front Axle Lower Wishbone / A-Arm assembly.
  • Component Symmetry: Asymmetric layout (Left-Hand and Right-Hand specific units; not interchangeable).
  • Material Matrix: High-strength stamped sheet steel body treated with anti-corrosive black electrophoresis paint.
  • Physical Dimensions: Approximate length of 510 mm, width of 235 mm, and body height of 62 mm.
  • Component Weight: 2.3 kg (approx. 5.07 lbs) per individual arm assembly.
  • Platform Adaptability: Form-fitted for the Nissan C11 chassis (Tiida, Latio, Wingroad Y12, Bluebird Sylphy G11, Cube Z12, and NV200 M20). [1, 2, 3, 4, 5, 6, 7, 8]
Integrated Hardware & Connection Specs
  • Ball Joint Integration: Integrated, factory press-fitted lower ball joint housing featuring a polymer-lined socket and hardened steel ball stud. [1, 2]
  • Ball Joint Cone Pin Size: Standard Ø 18 mm tapered diameter fitment. [1, 2]
  • Bushing Layout:
    • Front/Center Bushing: Inner horizontal steel-sleeve silent block.
    • Rear Bushing: Heavy-duty vertical lip bushing constructed of vulcanized natural rubber (Durometer hardness optimized for structural compliance and dampening road harshness). [1, 2, 3]
Genuine OEM Part Numbers & Aftermarket Cross-Reference
  • Right Hand (RH - Passenger Side):
    • Nissan Genuine OEM: 54500-ED000, 54500-1FU0A, 54500-1FU0B, 54500-1JY0A, 54500-ED00A
    • Aftermarket Identifiers: Delphi (TC2874), Febest (0224-C11RH) [1, 2]
  • Left Hand (LH - Driver Side):
    • Nissan Genuine OEM: 54501-ED000, 54501-1FU0A, 54501-1FU0B, 54501-1JY0A, 54501-ED00A, 54501-EL000
    • Aftermarket Identifiers: Delphi (TC2873), Febest (0224-C11LH) [1, 2, 3, 4, 5]
  • Stand-alone Ball Joint Component (If serviced separately): OEM 40160-ED000 / 40160-AX00B

Nissan NV200 Lower Arm Control

KSh3,500.00
Structural & Geometrical Specifications
  • Suspension Architecture: Lower Wishbone / A-Arm assembly designed for MacPherson Strut systems
  • Fitting Position: Front Axle (Asymmetric Left-Hand and Right-Hand specific units)
  • Material Composition: Stamped high-tensile steel sheet metal with structural reinforcement welds
  • Ball Joint Connection: Integrated press-fit vertical ball joint with a tapered stud spindle link
  • Bushing Points: Double rubber silent-block bushings (one horizontal inner barrel bush, one vertical rear rear-lip bush)
  • Chassis Compatibility: All M20 platform variants (1.5 dCi, 1.6L Petrol, e-NV200)
Genuine OEM & Cross-Reference Part Numbers
  • Right Hand (RH) Front Lower Arm:
    • Nissan OEM: 54500-JX00A, 54500-1FU0B, 54500-3LM0A, 54500-JX30A
  • Left Hand (LH) Front Lower Arm:
    • Nissan OEM: 54501-JX00A, 54501-1FU0B, 54501-3LM0A, 54501-JX30A
  • Aftermarket Cross-References: Blue Print (ADN186127 / ADN186128), Febest (0224-M20RH / 0224-M20LH)
Component Hardware Specifications
  • Ball Joint Stud Diameter: Standard 18 mm tapered fitment
  • Control Arm Weight: Approximately 3.4 kg to 3.8 kg per side (including pre-installed bushings and ball joint)
  • Surface Coating: Anti-corrosive black electrophoresis paint or powder coating for environmental salt and rust protection
  • Bushing Shore Hardness: 60–65 Shore A durometer natural rubber compound to withstand commercial transport load cycles

Toyota Noah Model 2017 Shock Absorber

KSh3,000.00
Front Shock Absorber (Strut) Specifications
  • System Type: Gas/Oil-Pressurized MacPherson Strut Assembly
  • Chassis Series: ZRR80G, ZRR80W, ZWR80G, ZWR80W, ZRR85 (2WD / 4WD configurations)
  • Damping Technology: Velocity-sensitive multi-stage valving, twin-tube internal architecture
  • Fitting Position: Front Axle (Asymmetric left and right specific orientation)
  • Genuine OEM Part Numbers:
    • Right Hand (RH): 48510-80799, 48510-80826, 48510-80655
    • Left Hand (LH): 48520-80475, 48520-80500, 48520-80356
  • Aftermarket Cross-Reference: KYB Excel-G Series (Part Numbers: 335068 (RH) / 335069 (LH))
Rear Shock Absorber Specifications
  • System Type: Gas-Charged, Twin-Tube Hydraulic Shock Damper
  • Damping Design: Double-acting telescopic hydraulic pressure
  • Fitting Position: Rear Axle (Symmetric / interchangeable left and right)
  • Mounting Configuration: Top eyelet/pin bush assembly with a reinforced lower rubber eyelet bushing
  • Genuine OEM Part Numbers: 48531-80784, 48531-80785, 48530-80426, 48540-80003
  • Aftermarket Cross-Reference: KYB Excel-G 3440109
Material & Internal Core Specifications
  • Piston Micro-Structure: Hardened carbon-steel rod with micro-grooved, mirror-smooth hard chrome coating to minimize seal friction.
  • Gas Media: Low-pressure Nitrogen gas (N₂) injection to minimize hydraulic fluid foaming, aeration, and thermal fading under load.
  • Fluid Seals: Multi-lip synthetic rubber sealing ring paired with an external dust/debris scraper ring.
  • Valving Control: Linear spring-loaded rebound disc system that self-adjusts based on piston movement frequency.

Toyota Voxy Model 2018 Shock Absorber

KSh3,000.00
Front Shock Absorber (Strut) Specifications
  • System Type: Gas/Oil-Pressurized MacPherson Strut Assembly
  • Damping Design: Twin-tube internal hydraulic architecture
  • Fitting Position: Front Axle (Left and Right specific asymmetric orientation)
  • Chassis Application: ZRR80G, ZRR80W, ZWR80G, ZWR80W, ZRR85G, ZRR85W (2WD & 4WD variants)
  • Genuine OEM Part Numbers:
    • Right Hand (RH): 48510-80826, 48510-80799, 48510-80655
    • Left Hand (LH): 48520-80500, 48520-80475, 48520-80356
  • Aftermarket Equivalents: KYB Excel-G Series (Part Numbers: 335068 for RH / 335069 for LH)
Rear Shock Absorber Specifications
  • System Type: Gas-Charged Telescopic Hydraulic Damper
  • Damping Design: Twin-Tube double-acting pressure system
  • Fitting Position: Rear Axle (Symmetric / interchangeable between left and right)
  • Mounting Structure: Top stem pin/eyelet joint with a reinforced bottom rubber eyelet bushing
  • Genuine OEM Part Numbers: 48531-80784, 48531-80785, 48530-80426, 48540-80003
  • Aftermarket Equivalents: KYB Excel-G Series (Part Number: 3440109)
Material & Structural Specifications
  • Piston Rod Construction: High-tensile, induction-hardened carbon steel finished with an anti-friction, hard-chrome plating.
  • Gas Element: Low-pressure Nitrogen gas (N₂) injection to actively suppress oil aeration, cavitation, and heat-induced damping fade.
  • Oil Seal Design: High-integrity multi-lip synthetic rubber seal integrated with a secondary external dirt-wiper ring.
  • Valving Mechanism: Velocity-sensitive, multi-stage rebound disc matrix that scales damping resistance relative to road-induced piston velocity.

Toyota Noah Model 2017 Shock Absorber

KSh3,000.00
Front Shock Absorber (Strut) Specifications
  • System Type: Gas/Oil-Pressurized MacPherson Strut Assembly [1]
  • Chassis Series: ZRR80G, ZRR80W, ZWR80G, ZWR80W, ZRR85 (2WD / 4WD configurations) [1]
  • Damping Technology: Velocity-sensitive multi-stage valving, twin-tube internal architecture
  • Fitting Position: Front Axle (Asymmetric left and right specific orientation) [1]
  • Genuine OEM Part Numbers:
    • Right Hand (RH): 48510-80799, 48510-80826, 48510-80655
    • Left Hand (LH): 48520-80475, 48520-80500, 48520-80356 [1]
  • Aftermarket Cross-Reference: KYB Excel-G Series (Part Numbers: 335068 (RH) / 335069 (LH)) [1]
Rear Shock Absorber Specifications
  • System Type: Gas-Charged, Twin-Tube Hydraulic Shock Damper
  • Damping Design: Double-acting telescopic hydraulic pressure
  • Fitting Position: Rear Axle (Symmetric / interchangeable left and right)
  • Mounting Configuration: Top eyelet/pin bush assembly with a reinforced lower rubber eyelet bushing
  • Genuine OEM Part Numbers: 48531-80784, 48531-80785, 48530-80426, 48540-80003
  • Aftermarket Cross-Reference: KYB Excel-G 3440109 [1, 2, 3]
Material & Internal Core Specifications
  • Piston Micro-Structure: Hardened carbon-steel rod with micro-grooved, mirror-smooth hard chrome coating to minimize seal friction.
  • Gas Media: Low-pressure Nitrogen gas (N₂) injection to minimize hydraulic fluid foaming, aeration, and thermal fading under load.
  • Fluid Seals: Multi-lip synthetic rubber sealing ring paired with an external dust/debris scraper ring.
  • Valving Control: Linear spring-loaded rebound disc system that self-adjusts based on piston movement frequency.

Toyota Voxy Model 2017 Shock Absorber

KSh3,500.00
Front Shock Absorber (Strut) Specifications
  • System Architecture: Oil/Gas-Pressurized MacPherson Strut Assembly
  • Fitting Position: Front Axle (Left / Right specific orientation)
  • Damping Mechanism: Twin-tube internal construction [1, 2]
  • Chassis Compatibility: ZRR80G, ZRR80W, ZWR80G, ZWR80W, ZRR85G (2WD & 4WD variants) [1]
  • Genuine OEM Part Numbers:
    • Right Side (RH): 48510-80826 (Marked: 48510-28540), 48510-80655, 48510-80799
    • Left Side (LH): 48520-80500 (Marked: 48520-28540), 48520-80356, 48520-80475 [1, 2]
  • Aftermarket Replacement: KYB Excel-G Series (Part Numbers: 335068 / 335069) [1, 2]
Rear Shock Absorber Specifications
  • System Architecture: Gas Pressure, Self-contained Damper
  • Damping Design: Twin-Tube
  • Fitting Position: Rear Axle (Left / Right interchangeable)
  • Mounting Assembly: Upper pin/eyelet joint and lower eyelet bushing
  • Genuine OEM Part Numbers: 48531-80784, 48530-80426, 48540-80003
  • Aftermarket Replacement: KYB Excel-G 3440109 [1, 2]
Internal Core & Material Specifications
  • Piston Rod: Induction-hardened carbon steel rod finished with low-friction hard chrome plating to minimize seal abrasion.
  • Gas Element: Charged with low-pressure Nitrogen (N₂) Gas to prevent hydraulic fluid aeration and foaming under continuous heat cycles.
  • Valving Matrix: Multi-stage, velocity-sensitive automatic rebound disc valves that dynamically adapt damping force to varying road conditions.
  • Seal Interface: Multi-lip synthetic rubber oil seal paired with an integrated dirt wiper to isolate internal fluid.

Toyota Voxy Model 2015 Shock Absorber

KSh3,000.00
Rear Shock Absorber Specifications
    • System/Design Type: Gas Pressure, Twin-Tube
    • Product Line / Category: OE Replacement (e.g., KYB Excel-G 3440109)
    • Fitting Position: Rear Axle (Left / Right)
    • Factory Lifespan: Approximately 80,000 to 100,000 km
    • Standard Mounting Type: Eye-to-pin or eye-to-eye bushing assembly
    • Genuine OEM Part Numbers: 48531-80784, 48530-80426, 48540-80003 [1, 2, 3, 4, 5]
Front Shock Absorber (Strut) Specifications
    • System/Design Type: Oil or Gas-Charged Strut Assembly
    • Fitting Position: Front Axle (Left / Right specific orientation)
    • Chassis Compatibility: ZRR80G, ZRR80W, ZWR80G, ZRR85G (2WD / 4WD variants)
    • Genuine OEM Part Numbers: 48510-80675 (Right), 48520-80477 (Left), 48510-80802
    • Aftermarket Replacement Parts: KYB 335068 / 335069 [1, 2, 3, 4, 5, 6, 7, 8]
Material & Build Specifications
  • Piston Rod: Heavy-duty, large diameter, induction-hardened, and hard-chrome plated for corrosion resistance.
  • Oil Seal: Multi-lip synthetic rubber seal designed with a contaminant wiper to keep hydraulic fluid locked inside.
  • Rod Guide: Sintered iron guide complete with a PTFE-bushed sliding surface for low friction and minimal rod wear.
  • Gas Charge: Low-pressure Nitrogen gas to reduce fluid aeration and foaming.

Toyota Voxy Model 2014 Shock Absorber

KSh3,000.00
Core Architectural Specifications (Front Struts)
    • Suspension System Layout: Independent MacPherson Strut.
    • Internal Shock Mechanics: Gas-Charged Twin-Tube low-pressure nitrogen gas technology (engineered to eliminate hydraulic fluid aeration and cavitation).
    • Strut Assembly Design: Structural, load-bearing suspension strut carrying the lower integrated spring seat plate and stabilizer link mounting tab.
    • Mounting Configuration: Symmetrical Top Pin / Stud upper chassis link fastened via a 3-bolt suspension tower support geometry, paired with a heavy-duty Saddle Bracket / Bottom Plate dual-bolt steering knuckle housing clamp layout.
    • Orientation: Asymmetrical, side-specific Left Hand (LH) and Right Hand (RH) directional assemblies.
Core Architectural Specifications (Rear Shocks)
    • Suspension System Layout: Semi-independent Torsion Beam / Axle Beam suspension system.
    • Damper Assembly Design: Standalone, non-load-bearing Telescopic Shock Absorber (operates entirely separated from the rear coil spring seats).
    • Internal Shock Mechanics: Gas-pressure twin-tube setup.
    • Mounting Configuration: Threaded Top Pin bushing stem adapter paired with a Bottom Eyelet sleeve cross-bolt mounting layout on the rear axle trailing arms.
    • Orientation: Symmetrical layout featuring identical, interchangeable units for both the left and right rear wheel hubs.
Chassis Platform Application
    • Chassis Platform Generation: Third-Generation Toyota Voxy (ZRR80 / ZRR85 / ZWR80 series, 2014 introduction year).
    • Drive Form Profiles: Internal valving dimensions and dampening stroke tolerances split strictly between standard Front-Wheel Drive (2WD / ZRR80) gasoline models, Hybrid models (2WD / ZWR80), and heavy-duty, higher-load All-Wheel Drive (4WD / ZRR85) variations.
Factory OEM & Aftermarket Cross-Reference Numbers
    • Toyota Factory Genuine OEM Base Roots:
        • Front Right Hand (RH): 48510-80800, 48510-28410, 48510-80674
        • Front Left Hand (LH): 48520-80436, 48520-28410, 48520-80327
        • Rear Axle Assemblies: 48530-80662, 48530-28630, 48530-D1010
    • KYB (Excel-G OE Replacement Series) Production Catalog Codes:
        • Front Right Hand (RH): 3340156
        • Front Left Hand (LH): 3340157
        • Rear Axle (Both Sides): 3440109
Structural Fastener Installation Torques
    • Strut-to-Steering Knuckle Clamp Bolts (Bottom dual-bolts): 164 Nm (121 ft-lbs).
    • Upper Chassis Tower Flange Mounting Nuts (3-bolt layout): 39 Nm (29 ft-lbs).
    • Center Strut Piston Rod Retaining Nut: 56 Nm (41 ft-lbs).
    • Front Sway Bar Stabilizer Link End Nuts: 74 Nm (55 ft-lbs).

Toyota Voxy Model 2010 Shock Absorber

KSh3,000.00
Core Architectural Specifications (Front Struts)
    • Suspension System Layout: Independent MacPherson Strut.
    • Internal Shock Mechanics: Gas-Charged Twin-Tube low-pressure nitrogen gas technology (calibrated to minimize hydraulic fluid aeration, foaming, and damping fade).
    • Strut Assembly Design: Structural, load-bearing suspension strut carrying the lower integrated spring seat plate.
    • Mounting Configuration: Symmetrical Top Pin / Stud upper chassis link fastened via a 3-bolt suspension tower support geometry, paired with a heavy-duty Saddle Bracket / Bottom Plate dual-bolt steering knuckle housing clamp layout.
    • Orientation: Asymmetrical, side-specific Left Hand (LH) and Right Hand (RH) directional assemblies.
Core Architectural Specifications (Rear Shocks)
    • Suspension System Layout: Semi-independent Torsion Beam / Axle Beam suspension system.
    • Damper Assembly Design: Standalone, non-load-bearing Telescopic Shock Absorber (operates entirely separated from the rear coil spring seats).
    • Internal Shock Mechanics: Gas-pressure twin-tube setup.
    • Mounting Configuration: Threaded Top Pin bushing stem adapter paired with a Bottom Eyelet sleeve cross-bolt mounting layout on the rear axle trailing arms.
    • Orientation: Symmetrical layout featuring identical, interchangeable units for both the left and right rear wheel hubs.
Chassis Platform Application
    • Chassis Platform Generation: Facelift Second-Generation Toyota Voxy (ZRR70 / ZRR75 series, 2010 production year).
    • Drive Form Profiles: Internal valving dimensions and dampening stroke tolerances split strictly between standard Front-Wheel Drive (2WD / ZRR70) chassis lines and heavy-duty, higher-load All-Wheel Drive (4WD / ZRR75) variations.
Factory OEM & Aftermarket Cross-Reference Numbers
    • Toyota Factory Genuine OEM Base Roots:
        • Front Right Hand (RH): 48510-80368, 48510-28320, 48510-80543
        • Front Left Hand (LH): 48520-80131, 48520-28320, 48520-80251
        • Rear Axle Assemblies: 48530-80547, 48540-29365
    • KYB (Excel-G OE Replacement Series) Production Catalog Codes:
        • Front Right Hand (RH): 335068 (Alternative: 339102)
        • Front Left Hand (LH): 335069 (Alternative: 339103)
        • Rear Axle (Both Sides): 344362
Structural Fastener Installation Torques
  • Strut-to-Steering Knuckle Clamp Bolts (Bottom dual-bolts): 164 Nm (121 ft-lbs).
  • Upper Chassis Tower Flange Mounting Nuts (3-bolt layout): 39 Nm (29 ft-lbs).
  • Center Strut Piston Rod Retaining Nut: 56 Nm (41 ft-lbs).
  • Front Sway Bar Stabilizer Link End Nuts: 74 Nm (55 ft-lbs).

Toyota Noah Shock Model 2012

KSh3,000.00
Core Architectural Specifications (Front Struts)
  • Suspension System Layout: Independent MacPherson Strut front suspension.
  • Internal Shock Mechanics: Gas-Charged Twin-Tube low-pressure nitrogen gas technology (calibrated to eliminate hydraulic fluid aeration, cavitation, and damping fade).
  • Strut Assembly Design: Structural, load-bearing suspension strut carrying the lower integrated spring seat plate.
  • Mounting Configuration: Symmetrical Top Pin / Stud upper chassis link fastened via a 3-bolt suspension tower support, paired with a heavy-duty Saddle Bracket / Bottom Plate dual-bolt steering knuckle housing clamp layout.
  • Orientation: Asymmetrical, side-specific Left Hand (LH) and Right Hand (RH) directional assemblies.
Core Architectural Specifications (Rear Shocks)
  • Suspension System Layout: Semi-independent Torsion Beam / Axle Beam suspension system.
  • Damper Assembly Design: Standalone, non-load-bearing Telescopic Shock Absorber (operates entirely separated from the rear coil spring seats).
  • Internal Shock Mechanics: Low-pressure gas-charged twin-tube setup.
  • Mounting Configuration: Threaded Top Pin bushing stem adapter paired with a Bottom Eyelet sleeve through-bolt mounting layout on the rear axle trailing arms.
  • Orientation: Symmetrical layout featuring identical, interchangeable units for both the left and right rear positions.
Chassis Platform Application
  • Chassis Platform Generation: Late Second-Generation Toyota Noah (ZRR70 / ZRR75 series, 2012 production year).
  • Drive Form Profiles: Internal valving dimensions, stroke limits, and damping rates are split strictly between standard Front-Wheel Drive (2WD / ZRR70) chassis lines and heavy-duty, higher-load All-Wheel Drive (4WD / ZRR75) variations.
Factory OEM & Aftermarket Cross-Reference Numbers
  • Toyota Factory Genuine OEM Base Roots:
    • Front Right Hand (RH): 48510-80543, 48510-28230, 48510-80396
    • Front Left Hand (LH): 48520-80289, 48520-28230, 48520-80199
    • Rear Axle Assemblies: 48530-80547, 48530-28560
  • KYB (Excel-G OE Replacement Series) Production Catalog Codes:
    • Front Right Hand (RH): 339102
    • Front Left Hand (LH): 339103
    • Rear Axle (Both Sides): 344362
Structural Fastener Installation Torques
  • Strut-to-Steering Knuckle Clamp Bolts (Bottom dual-bolts): 164 Nm (121 ft-lbs).
  • Upper Chassis Suspension Tower Flange Nuts (3-bolt layout): 39 Nm (29 ft-lbs).
  • Center Strut Piston Rod Retaining Nut: 56 Nm (41 ft-lbs).
  • Front Sway Bar Stabilizer Link End Nuts: 74 Nm (55 ft-lbs).

Toyota Noah Shock Model 2010

KSh3,000.00
Core Architectural Specifications (Front Struts)
  • Suspension System Layout: Independent MacPherson Strut front suspension.
  • Internal Shock Mechanics: Gas-Charged Twin-Tube low-pressure nitrogen gas technology (calibrated to minimize hydraulic fluid aeration, foaming, and damping fade).
  • Strut Assembly Design: Structural, load-bearing suspension strut carrying the lower integrated spring seat plate.
  • Mounting Configuration: Symmetrical Top Pin / Stud upper chassis link fastened via a 3-bolt suspension tower support, paired with a heavy-duty Saddle Bracket / Bottom Plate dual-bolt steering knuckle housing clamp layout.
  • Orientation: Asymmetrical, side-specific Left Hand (LH) and Right Hand (RH) directional assemblies.
Core Architectural Specifications (Rear Shocks)
  • Suspension System Layout: Semi-independent Torsion Beam / Axle Beam suspension system.
  • Damper Assembly Design: Standalone, non-load-bearing Telescopic Shock Absorber (operates entirely separated from the rear coil spring seats).
  • Internal Shock Mechanics: Low-pressure gas-charged twin-tube setup.
  • Mounting Configuration: Threaded Top Pin bushing stem adapter paired with a Bottom Eyelet sleeve through-bolt mounting layout on the rear axle trailing arms.
  • Orientation: Symmetrical layout featuring identical, interchangeable units for both the left and right rear positions.
Chassis Platform Application
  • Chassis Platform Generation: Facelift Second-Generation Toyota Noah (ZRR70 / ZRR75 series, 2010 production year).
  • Drive Form Profiles: Internal valving dimensions, stroke limits, and damping rates are split strictly between standard Front-Wheel Drive (2WD / ZRR70) chassis lines and heavy-duty, higher-load All-Wheel Drive (4WD / ZRR75) variations.
Factory OEM & Aftermarket Cross-Reference Numbers
  • Toyota Factory Genuine OEM Base Roots:
    • Front Right Hand (RH): 48510-80543, 48510-28230, 48510-80396
    • Front Left Hand (LH): 48520-80289, 48520-28230, 48520-80199
    • Rear Axle Assemblies: 48530-80547, 48530-28560
  • KYB (Excel-G OE Replacement Series) Production Catalog Codes:
    • Front Right Hand (RH): 339102
    • Front Left Hand (LH): 339103
    • Rear Axle (Both Sides): 344362
Structural Fastener Installation Torques
  • Strut-to-Steering Knuckle Clamp Bolts (Bottom dual-bolts): 164 Nm (121 ft-lbs).
  • Upper Chassis Suspension Tower Flange Nuts (3-bolt layout): 39 Nm (29 ft-lbs).
  • Center Strut Piston Rod Retaining Nut: 56 Nm (41 ft-lbs).
  • Front Sway Bar Stabilizer Link End Nuts: 74 Nm (55 ft-lbs).

Toyota Voxy Shock Model 2008

KSh3,500.00
Core Architectural Specifications (Front Struts)
  • Suspension System Layout: Independent MacPherson Strut.
  • Internal Shock Mechanics: Gas-Charged Twin-Tube low-pressure nitrogen gas technology to eliminate internal hydraulic fluid aeration and cavitation.
  • Strut Assembly Design: Structural, load-bearing suspension strut carrying the lower integrated spring seat plate.
  • Mounting Configuration: Symmetrical Top Pin / Stud upper chassis link fastened via a 3-bolt suspension tower support geometry, paired with a heavy-duty Saddle Bracket / Bottom Plate dual-bolt steering knuckle housing clamp layout.
  • Orientation: Asymmetrical, side-specific Left Hand (LH) and Right Hand (RH) directional assemblies.
Core Architectural Specifications (Rear Shocks)
  • Suspension System Layout: Semi-independent Torsion Beam / Axle Beam suspension system.
  • Damper Assembly Design: Standalone, non-load-bearing Telescopic Shock Absorber (operates entirely separated from the rear coil spring seats).
  • Internal Shock Mechanics: Gas-pressure twin-tube setup.
  • Mounting Configuration: Threaded Top Pin bushing stem adapter paired with a Bottom Eyelet sleeve cross-bolt mounting layout on the rear axle trailing arms.
  • Orientation: Symmetrical layout featuring identical, interchangeable units for both the left and right rear wheel hubs.
Chassis Platform Application
  • Chassis Platform Generation: Second-Generation Toyota Voxy (ZRR70 / ZRR75 series).
  • Drive Form Profiles: Internal valving dimensions and dampening stroke tolerances split strictly between standard Front-Wheel Drive (2WD / ZRR70) chassis lines and heavy-duty, higher-load All-Wheel Drive (4WD / ZRR75) variations.
Factory OEM & Aftermarket Cross-Reference Numbers
  • Toyota Factory Genuine OEM Base Roots:
    • Front Right Hand (RH): 48510-80368, 48510-28320
    • Front Left Hand (LH): 48520-80131, 48520-28320, 48520-80251
    • Rear Axle Assemblies: 48530-80547, 48540-29365
  • KYB (Excel-G OE Replacement Series) Production Catalog Codes:
    • Front Right Hand (RH): 335068
    • Front Left Hand (LH): 335069
    • Rear Axle (Both Sides): 344362 (Alternative legacy code: 344480)
Structural Fastener Installation Torques
  • Strut-to-Steering Knuckle Clamp Bolts (Bottom dual-bolts): 164 Nm (121 ft-lbs).
  • Upper Chassis Tower Flange Mounting Nuts (3-bolt layout): 39 Nm (29 ft-lbs).
  • Center Strut Piston Rod Retaining Nut: 56 Nm (41 ft-lbs).
  • Front Sway Bar Stabilizer Link End Nuts: 74 Nm (55 ft-lbs).

Toyota Noah Model 2008 Front Shock

KSh3,500.00
Core Architectural Specifications
    • Suspension Layout: Independent MacPherson Strut front suspension system.
    • Internal Shock Mechanics: Gas-Charged Twin-Tube low-pressure nitrogen gas technology (calibrated to eliminate hydraulic fluid aeration and foaming over rough road surfaces).
    • Strut Assembly Design: Structural Suspension Strut (acts as a vital load-bearing suspension path and mechanical carrier for the front steering knuckle).
    • Mounting Configuration: Symmetrical Top Pin / Stud upper chassis link fastened via a 3-bolt tower pattern, paired with a heavy-duty Saddle Bracket / Bottom Plate dual-bolt steering knuckle housing clamp layout.
    • Orientation: Asymmetrical, side-specific Left Hand (LH) and Right Hand (RH) directional assemblies.
Chassis Platform Application
    • Chassis Platform Generation: Second-Generation Toyota Noah (ZRR70 / ZRR75 series).
    • Drive Form Configurations: Internal valving dimensions and dampening rates are split strictly between standard Front-Wheel Drive (2WD / ZRR70) chassis code lines and heavy-duty, higher-load All-Wheel Drive (4WD / ZRR75) variations.
Factory OEM & Aftermarket Cross-Reference Numbers
    • Toyota Factory Genuine OEM Base Roots:
        • Front Right Hand (RH): 48510-80396, 48510-80543, 48510-28230
        • Front Left Hand (LH): 48520-80199, 48520-80289, 48520-28230
    • KYB (Excel-G OE Replacement Series) Production Catalog Codes:
        • Front Right Hand (RH): 339102
        • Front Left Hand (LH): 339103
Structural Fastener Installation Torques
  • Strut-to-Steering Knuckle Clamp Bolts (Bottom dual-bolts): 164 Nm (121 ft-lbs).
  • Upper Chassis Tower Flange Mounting Nuts (3-bolt layout): 39 Nm (29 ft-lbs).
  • Center Strut Piston Rod Retaining Nut: 56 Nm (41 ft-lbs).
  • Front Sway Bar Stabilizer Link End Nuts: 74 Nm (55 ft-lbs).
Showing 196 of 641 results
Please select your product
Product has been added to your cart
Compare (0)