Harrier 240 Rear Shock
KSh5,000.00 Buy Via WhatsappCore Architectural Specifications (Rear Struts)
- Suspension Layout: Independent MacPherson Strut rear suspension system.
- Internal Shock Mechanics: Gas-Charged Twin-Tube low-pressure nitrogen gas configuration (engineered to eliminate hydraulic fluid aeration and foaming on rough terrain).
- Strut Assembly Design: Structural Suspension Strut (acts as a load-bearing member with an integrated lower spring seat plate).
- Mounting Configuration: 3-bolt upper chassis tower pattern paired with a bottom dual-bolt steering knuckle mounting bracket.
- Orientation: Asymmetrical, side-specific Left Hand (LH) and Right Hand (RH) directional assemblies.
Generation-Specific Chassis Variations (Harrier 240 / 2.4L 2AZ-FE)
The mechanical valving and mounting dimensions are split across the two primary production generations:
1. First Generation: X10 Platform (1997–2003) — ACU10 (2WD) / ACU15 (4WD)
- Standard 2WD Aftermarket KYB References:
- Rear Right Hand (RH): 334261
- Rear Left Hand (LH): 334262
- Standard 4WD Aftermarket KYB References:
- Rear Right Hand (RH): 334243
- Rear Left Hand (LH): 334244
- Factory Genuine OEM Reference Roots: 48530-49035, 48540-49035.
2. Second Generation: X30 Platform (2003–2013) — ACU30W (2WD) / ACU35W (4WD)
- Standard 2WD Aftermarket KYB References:
- Rear Right Hand (RH): 334400
- Rear Left Hand (LH): 334401
- Standard 4WD Aftermarket KYB References:
- Rear Right Hand (RH): 334394
- Rear Left Hand (LH): 334395
- Factory Genuine OEM Reference Roots: 48530-49275, 48530-49285, 48540-49195.
Structural Fastener Installation Torques
- Strut-to-Steering Knuckle Clamp Bolts (Bottom dual-bolts): 252 Nm (186 ft-lbs).
- Upper Chassis Tower Flange Mounting Nuts (3-bolt layout): 39 Nm (29 ft-lbs).
- Center Strut Piston Rod Retaining Nut: 49 Nm (36 ft-lbs).
Nissan B15 Shocks
KSh3,000.00 Buy Via WhatsappCore Architectural Specifications (Front Struts)
- Suspension Layout: Independent MacPherson Strut.
- Internal Shock Mechanics: Gas-Charged Twin-Tube low-pressure nitrogen configuration (engineered to reduce hydraulic fluid aeration and foaming on rough terrain).
- Strut Assembly Design: Load-bearing structural suspension strut.
- Mounting Configuration: 3-bolt upper triangular tower mounting pattern paired with a bottom dual-bolt steering knuckle mounting saddle bracket.
- Orientation: Asymmetrical, side-specific Left Hand (LH) and Right Hand (RH) directional assemblies.
Core Architectural Specifications (Rear Shocks)
- Suspension Layout Compatibility: Multi-Link Beam Axle or rigid trailing link rear suspension setup (depending on standard 2WD or 4WD chassis configurations).
- Shock Assembly Design: Standalone, non-load-bearing Telescopic Shock Absorber (damper operates completely separate from the independent coil spring seat).
- Mounting Configuration: Top Pin threaded rod connection paired with a Bottom Eyelet sleeve through-bolt bushing.
- Orientation: Symmetrical layout (identical interchangeable units for both Left and Right rear positions).
Chassis & Drive Train Variations (Nissan Sunny B15 / Sentra Platform)
- 2WD (Front-Wheel Drive) vs. 4WD (FNB15 Chassis): Rear shock dampening rates and internal oil-valving dimensions are split strictly between standard Front-Wheel Drive models and the heavier-duty, higher-load All-Wheel Drive (FNB15 / i-Four) platforms.
- Material Composition: Induction-hardened carbon steel piston rods paired with premium multi-lip Nitrile rubber (NBR) oil seals to survive demanding dust conditions.
Factory OEM & Aftermarket Cross-Reference Numbers
- Nissan Genuine Factory JDM OEM Roots:
- Front Right Hand (RH): 54302-4M403, 54302-4M425, 54302-WD025
- Front Left Hand (LH): 54303-4M403, 54303-4M425, 54303-WD025
- Rear Axle外 Dampers: 56210-4M400, 56210-4M425, 56210-4M725
- KYB (Excel-G OE Replacement Series) Part Numbers:
- Front Right Hand (RH): 333310
- Front Left Hand (LH): 333311
- Rear Axle (Both Sides): 341279
Toyota Fielder Model 2012 Heavy Duty Springs Ex-Japan
KSh10,000.00 Buy Via WhatsappCore Metallurgical & Coil Geometry Specs
- Coil Spring Design Profile: Cylindrical, Linear Rate Heavy-Duty Aftermarket Coil Spring configuration.
- Wire Cross-Section Diameter (Thickness): 13.2 mm (Front Axle) | 12.5 mm (Rear Axle). Heavy-duty reinforced specification; increased from the standard factory stock diameter to lift load capacity.
- Spring Outer Diameter (Ø): 144 mm (Front) | 106 mm (Rear).
- Total Free Uncompressed Length (Height): 350 mm (Front) | 340 mm (Rear).
- Total Active Coil Windings: 5.5 coils (Front) | 7.75 coils (Rear).
- Material Composition: Induction-hardened 54SiCr6 / 55CrSi High-Tensile Silicon-Chromium Spring Steel alloy, finished with an impact-resistant, anti-corrosion gloss powder coating layer.
Functional Suspension Dynamics & Performance Ratings
- Spring Load Rate Classification: Heavy-Duty / Reinforced Cargo & Rough-Road Specification (Ex-Japan aftermarket source).
- Spring Stiffness Constant (Rate): 32 N/mm (Front) | 29 N/mm (Rear). Engineered with a 25% to 35% increase in load-bearing stiffness compared to the highly compliant factory JDM setup.
- Primary Mechanics Profile: Specifically calibrated to eliminate station-wagon rear sagging under full passenger load or cargo capacity, minimize vehicle body roll during cornering transitions, and maximize ground clearance over uneven road infrastructure.
Target Chassis Code Applications
- Toyota Platform Series: Eleventh-Generation Corolla Fielder Wagon—NRE161G (1.3L 2WD), NZE161G (1.5L 2WD), ZRE162G (1.8L 2WD), NZE164G (1.5L 4WD), NKE165G (1.5L Hybrid 2WD).
- Cross-Platform JDM Twins: Directly cross-compatible with the corresponding Toyota Corolla Axio Sedan (NZE161 / NRE161 / NKE165) platform of identical production years.
Industry Cross-References & Manufacturer Part Bases
- Toyota Factory Standard Base Part Roots (For dimensional reference): 48131-12F20 (Front) | 48231-12E70 (Rear).
- Premium Aftermarket Heavy-Duty Alternatives:
- OBK (Osaka Bane Inc.) Heavy-Duty Coil: Blue-painted reinforced aftermarket catalog series.
- Cobra Springs Heavy-Duty Series: Specialized reinforced performance specification matrices matching NZE161G parameters.
- Lesjöfors Heavy-Duty Coil Reference: 4292631 (Front) | 4292644 (Rear Heavy Duty/Cargo alternative series).
Toyota Fielder 2005 Heavy Duty Springs Ex-Japan
KSh10,000.00 Buy Via WhatsappCore Metallurgical & Coil Geometry Specs
- Coil Spring Design Profile: Cylindrical, Linear Rate Heavy-Duty Aftermarket Coil Spring configuration.
- Wire Cross-Section Diameter (Thickness): 12.5 mm (Front Axle) | 12.0 mm (Rear Axle). Heavy-duty reinforced specification; increased from the standard factory stock diameter to lift load capacity.
- Spring Outer Diameter (Ø): 148 mm (Front) | 140 mm (Rear).
- Total Free Uncompressed Length (Height): 340 mm (Front) | 315 mm (Rear).
- Total Active Coil Windings: 5.5 coils (Front) | 6.25 coils (Rear).
- Material Composition: Induction-hardened 54SiCr6 / 55CrSi High-Tensile Silicon-Chromium Spring Steel alloy, finished with an impact-resistant, anti-corrosion gloss powder coating layer.
Functional Suspension Dynamics & Performance Ratings
- Spring Load Rate Classification: Heavy-Duty / Reinforced Cargo & Rough-Road Specification (Ex-Japan aftermarket source).
- Spring Stiffness Constant (Rate): 30 N/mm (Front) | 27 N/mm (Rear). Engineered with a 25% to 35% increase in load-bearing stiffness compared to the highly compliant factory JDM setup.
- Primary Mechanics Profile: Specifically calibrated to eliminate rear station-wagon sagging under full passenger load or cargo capacity, minimize vehicle body roll during cornering transitions, and maximize ground clearance over uneven road infrastructure.
Target Chassis Code Applications
- Toyota Platform Series: Ninth-Generation Corolla Fielder Wagon—NZE121G (1.5L 2WD), ZZE122G (1.8L 2WD), ZZE123G (1.8L 2WD), NZE124G (1.5L 4WD), ZZE124G (1.8L 4WD).
- Cross-Platform JDM Twins: Directly cross-compatible with the corresponding Toyota Corolla Sedan (NZE121 / ZZE122) and Toyota Corolla RunX / Allex (NZE121 / ZZE123) hatchbacks of identical production years.
Industry Cross-References & Manufacturer Part Bases
- Toyota Factory Standard Base Part Roots (For dimensional reference): 48131-1A790 (Front) | 48231-1A800 (Rear).
- Premium Aftermarket Heavy-Duty Alternatives:
- OBK (Osaka Bane Inc.) Heavy-Duty Coil: Blue-painted reinforced aftermarket catalog series.
- Cobra Springs Heavy-Duty Series: Specialized reinforced performance specification matrices matching NZE121 parameters.
- Lesjöfors Heavy-Duty Coil Reference: 4292557 (Front) | 4292569 (Rear Heavy Duty/Cargo alternative series).
Axio 2007 Heavy Duty Springs Ex-Japan
KSh10,000.00 Buy Via WhatsappCore Metallurgical & Coil Geometry Specs
- Coil Spring Design Profile: Cylindrical, Linear Rate Heavy-Duty Aftermarket Coil Spring configuration.
- Wire Cross-Section Diameter (Thickness): 13.0 mm (Front Axle) | 12.5 mm (Rear Axle). Heavy-duty reinforced specification; increased from the standard factory stock diameter to lift load capacity.
- Spring Outer Diameter (Ø): 142 mm (Front) | 106 mm (Rear).
- Total Free Uncompressed Length (Height): 345 mm (Front) | 335 mm (Rear).
- Total Active Coil Windings: 5.5 coils (Front) | 7.5 coils (Rear).
- Material Composition: Induction-hardened 54SiCr6 / 55CrSi High-Tensile Silicon-Chromium Spring Steel alloy, finished with an impact-resistant, anti-corrosion gloss powder coating layer.
Functional Suspension Dynamics & Performance Ratings
- Spring Load Rate Classification: Heavy-Duty / Reinforced Cargo & Rough-Road Specification (Ex-Japan aftermarket source).
- Spring Stiffness Constant (Rate): 31 N/mm (Front) | 28 N/mm (Rear). Engineered with a 25% to 35% increase in load-bearing stiffness compared to the highly compliant factory JDM setup.
- Primary Mechanics Profile: Specifically calibrated to eliminate rear-end sagging under full passenger load or cargo capacity, minimize vehicle body roll during cornering transitions, and maximize ground clearance over uneven road infrastructure.
Target Chassis Code Applications
- Toyota Platform Series: Tenth-Generation Toyota Corolla Axio Sedan (NZE141 1.5L 2WD / ZRE142 1.8L 2WD / NZE144 1.5L 4WD / ZRE144 1.8L 4WD series).
- Cross-Platform JDM Twins: Directly cross-compatible with the corresponding Toyota Corolla Fielder (NZE141G / ZRE142G / NZE144G) station wagon platform of identical production years.
Industry Cross-References & Manufacturer Part Bases
- Toyota Factory Standard Base Part Roots (For dimensional reference): 48131-12A60 (Front) | 48231-12A50 (Rear).
- Premium Aftermarket Heavy-Duty Alternatives:
- OBK (Osaka Bane Inc.) Heavy-Duty Coil: Blue-painted reinforced aftermarket catalog series.
- Cobra Springs Heavy-Duty Series: Specialized reinforced performance specification matrices matching NZE141 parameters.
- Lesjöfors Heavy-Duty Coil Reference: 4292601 (Front) | 4292618 (Rear Heavy Duty/Cargo alternative series).
Passo 2018 Heavy Duty Coil Springs
KSh10,000.00 Buy Via WhatsappCore Metallurgical & Coil Geometry Specs
-
- Coil Spring Design Profile: Cylindrical, Linear Rate Heavy-Duty Aftermarket Coil Spring configuration.
- Wire Cross-Section Diameter (Thickness): 11.0 mm (Front Axle) | 10.5 mm (Rear Axle). Reinforced aftermarket specification; increased from standard factory stock wire to elevate load handling capability.
- Spring Outer Diameter (Ø): 114 mm to 122 mm (Axle-position dependent).
- Total Free Uncompressed Length (Height): 315 mm – 330 mm (Calibrated to maintain optimal unladen vehicle ride height and prevent sagging).
- Total Active Coil Windings: 5.5 to 6.25 coils.
- Material Composition: Induction-hardened 55CrSi High-Tensile Silicon-Chromium Spring Steel alloy, finished with an impact-resistant, anti-corrosion gloss powder coating layer.
Functional Suspension Dynamics & Performance Ratings
-
- Spring Load Rate Classification: Heavy-Duty / Reinforced Cargo & Rough-Road Specification.
- Spring Stiffness Constant (Rate): 24 N/mm (Front) | 21 N/mm (Rear). Engineered with a 25% to 35% increase in load-bearing stiffness compared to the highly compliant factory JDM setup.
- Primary Mechanics Profile: Specifically calibrated to eliminate rear-end sagging under full passenger load or cargo capacity, minimize vehicle body roll during cornering transitions, and maximize ground clearance over uneven road infrastructure.
Target Chassis Code Applications
-
- Toyota Platform Series: Third-Generation Toyota Passo (M700A 2WD / M710A 4WD series).
- Cross-Platform Daihatsu Twin: Directly cross-compatible with the corresponding Daihatsu Boon (M700S / M710S) chassis platform configuration of identical production years.
Industry Cross-References & Manufacturer Part Bases
-
- Toyota Factory Standard Base Part Roots (For dimensional reference): 48131-B1230 (Front) | 48231-B1130 (Rear).
- Premium Aftermarket Heavy-Duty/Performance Alternatives:
-
- Cobra Springs Heavy-Duty Series: Specialized reinforced performance specification matrices matching M700 chassis parameters [inferred].
- OBK (Osaka Bane Inc.) Heavy-Duty Coil: Blue-painted reinforced aftermarket catalog series.
- Lesjöfors / Kilen Reinforced Reference: Heavy-duty alternate variant series optimized for enhanced cargo capabilities.
-
Daihatsu Mira Heavy Duty Coil Spring
KSh8,000.00 Buy Via WhatsappCore Metallurgical & Coil Geometry Specs
-
- Coil Spring Design Profile: Cylindrical, Linear Rate Heavy-Duty Aftermarket Coil Spring configuration.
- Wire Cross-Section Diameter (Thickness): 9.5 mm to 10.5 mm (reinforced aftermarket specification; increased from the standard 8.5 mm factory stock wire diameter to improve load handling and prevent bottoming out).
- Spring Outer Diameter (Ø): 102 mm to 110 mm (varies structurally between front and rear axle shapes).
- Total Free Uncompressed Length (Height): 285 mm to 310 mm (depending on the specific chassis variation to maintain proper unladen vehicle ride height).
- Total Active Coil Windings: 5.5 to 6.5 coils.
- Material Composition: Induction-hardened 54SiCr6 / 55CrSi High-Tensile Silicon-Chromium Spring Steel alloy, finished with an anti-corrosion, impact-resistant heavy powder coating layer.
Functional Suspension Dynamics & Performance Ratings
-
- Spring Load Rate Classification: Heavy-Duty / Reinforced Cargo Specification.
- Spring Stiffness Constant (Rate): 22 N/mm to 26 N/mm (engineered with an approximate 20% to 30% increase in load-bearing stiffness compared to the highly compliant factory JDM setup).
- Primary Mechanics Profile: Specifically calibrated to eliminate rear-end sagging when carrying full rear passengers or cargo, reduce body roll under cornering loads, and maximize ground clearance on uneven road surfaces.
Target Chassis Code Applications
-
- Daihatsu Platform Series: L275S, L275V, L285S (4WD), LA300S, LA310S, LA350S, LA360S (Mira e:S series).
- Cross-Platform Toyota/Subaru Twins: Directly compatible with identical platform derivatives: Toyota Pixis Epoch and Subaru Pleo / Mira Custom chassis frames of corresponding production years.
Industry Cross-References & Manufacturer Part Bases
- Daihatsu Factory Standard Base Part Roots (For dimensional reference): 48131-B2010, 48131-B2560 (Front) | 48231-B2010, 48231-B2A80 (Rear).
- Premium Aftermarket Heavy-Duty/Performance Alternatives:
- Cobra Springs Heavy-Duty Series: Specialized European reinforced specification matrices matching L275/LA300 parameters.
- OBK (Osaka Bane Inc.) Heavy-Duty Coil: Blue-painted reinforced variant catalog references.
- Lesjöfors Heavy-Duty Coil Reference: 4215607 / 4215609 (Reinforced / Cargo alternative series)
Toyota BB Front Shocks
KSh3,000.00 Buy Via WhatsappCore Architectural Specifications
- Suspension Architecture: Independent MacPherson Strut setup. [1, 2]
- Internal Strut Mechanics: Gas-Pressure Twin-Tube low-pressure nitrogen configuration (OEA standard engineered to prevent hydraulic fluid cavitation and foaming over uneven road surfaces). [1, 2]
- Shock Absorber Design: Structural Suspension Strut (operates as a critical load-bearing suspension path and structural carrier for the front steering knuckle assembly). [1, 2]
- Mounting Configuration: Symmetrical Top Pin / Stud upper chassis link fastened via a 3-bolt tower pattern, paired with a heavy-duty Saddle Bracket / Bottom Plate dual-bolt steering knuckle housing clamp layout. [1, 2, 3]
Generation & Chassis Variations
The specific internal valving metrics and structural dimension baselines split precisely across the two prominent Japanese Domestic Market (JDM) production generations:
1. First Generation: NCP30 Platform (2000–2005) — NCP30 (1.3L 2NZ-FE) / NCP31 (1.5L 1NZ-FE) / NCP35 (4WD)
- Chassis Setup: Shared global Toyota NBC platform footprint. [1, 2]
- KYB (Excel-G Series) Aftermarket Part Numbers:
- Front Right Hand (RH): 333368
- Front Left Hand (LH): 333369
- Subaru/Toyota Genuine OEM Base Roots: 48510-59135, 48520-59135, 48510-49035. [1]
2. Second Generation: QNC20 Platform (2006–2016) — QNC20 (1.3L K3-VE) / QNC21 (1.5L 3SZ-VE) / QNC25 (4WD)
- Chassis Setup: Co-developed Daihatsu sub-compact baseline matrix. [1, 2]
- KYB (Excel-G Series) Aftermarket Part Numbers:
- Subaru/Toyota Genuine OEM Base Roots: 48510-B1030, 48520-B1030, 48510-B1070. [1]
Structural Fastener Installation Torques
Daihatsu Mirabrake Discs
KSh2,500.00 Buy Via WhatsappFront Brake Disc Dimensions & Geometry
The technical specifications for the front brake discs (rotors) of the modern Daihatsu Mira (L275 and LA300/e:S chassis platform) vary slightly depending on whether the sub-trim package utilizes a Solid or Vented rotor design: [1, 2]
- Outer Diameter (Ø): 211.0 mm (Standard baseline/e:S JDM trims) up to 234.0 mm (Large-caliper / Custom turbo configurations). [1, 2, 3, 4, 5]
- Nominal Thickness (New):
- Minimum Thickness / Wear Limit:
- Total Structural Height: 41.0 mm. [1, 2, 3]
- Centering / Hub Pilot Bore Diameter: 54.0 mm to 55.0 mm. [1, 2, 3]
- Material Composition: G3000 Grade high-carbon grey cast iron metallurgy for thermal dissipation.
Wheel Mount & Hub Interface
- Lug Bolt Hole Arrangement: 4 Holes.
- Pitch Circle Diameter (PCD): 4 x 100 mm.
- Wheel Bolt Bore Diameter: 13.8 mm. [1, 2, 3, 4]
Factory OEM & Aftermarket Cross-Reference Numbers
- Daihatsu Genuine Factory OEM Part Roots: 43512-B2140, 43512-B2100, 43512-97201.
- Major Aftermarket Technical Cross-References:
Structural Fastener Installation Torques
Suzuki Wagon R Wheel Hub Bearing
KSh4,500.00 Buy Via WhatsappFront Wheel Hub & Bearing Specifications (Press-In Split Type)
- Bearing Style: Generation 1 Press-In Sealed Double-Row Angular Contact Ball Bearing. The standalone driven hub flange presses into the steering knuckle-seated bearing.
- Integrated Sensor Technology: Features an integrated magnetic multi-pole ABS encoder ring built directly into the inner rubber oil seal face on one side of the bearing.
- Axle Location: Front Axle (Symmetric Left / Right configuration).
- Front Bearing Core Dimensions: Inner Diameter: 35.0 mm | Outer Diameter: 64.0 mm | Width / Thickness: 37.0 mm.
- Wheel Lug Pattern Configuration: 4 Holes.
- Pitch Circle Diameter (PCD): 4 x 100 mm.
- Centering / Hub Pilot Outer Diameter: 54.0 mm.
- Internal Drive Splines: 23 Internal Teeth (interfacing with the outer CV joint axle stub).
- Suzuki Genuine Factory OEM Part Numbers: 43440-58J00, 43440-78A20, 43440-84F00.
- Major Aftermarket Cross-References: NSK 35BWD24, GMB GH30330, Koyo DAC35640037.
Rear Wheel Hub & Bearing Unit Specifications (2WD Models)
- Design Configuration: Built directly into the Rear Brake Drum assembly (Generation 1 sealed press-in bearing integrated inside the brake drum center cavity, spinning on a non-driven spindle shaft stud).
- Axle Position: Rear Axle (Symmetric Left / Right mounting geometry).
- Wheel Lug Arrangement: 4 Holes.
- Rear Pitch Circle Diameter (PCD): 4 x 100 mm.
- Rear Bearing Core Dimensions: Inner Diameter: 25.0 mm | Outer Diameter: 52.0 mm | Width / Thickness: 43.0 mm.
- Material Composition: Forged grey alloy iron drum base matching induction-hardened GCr15 High-Carbon Chromium Bearing Steel internals.
- Suzuki Genuine Factory OEM Part Numbers (Rear): 46860-76G00, 46860-76G04, 46860-60G00.
- Major Aftermarket Cross-References (Rear): NSK 25BWD01, Koyo DAC25520043, Febest DAC25520043-KIT.
Suzuki Alto Model 2018 Brake Discs
KSh3,000.00 Buy Via WhatsappFront Brake Disc Dimensions & Geometry
- Outer Diameter (Ø): 231.0 mm (Standard HA36 series).
- Nominal Thickness: 17.0 mm (Standard models) or 20.0 mm (Turbo RS / Works / high-trim configurations).
- Minimum Thickness / Wear Limit: 15.0 mm (for 17mm nominal discs) or 18.0 mm (for 20mm nominal discs). Discard and replace immediately if worn below these limits.
- Total Structural Height: 49.1 mm to 51.4 mm.
- Centering / Pilot Bore Diameter: 60.0 mm.
- Material Composition: High-carbon grey cast iron metallurgy for optimal thermal resistance. [1, 2, 3, 4, 5, 6, 7, 8]
Wheel Mount & Hub Interface
- Lug Bolt Hole Arrangement: 4 Holes.
- Pitch Circle Diameter (PCD): 4 x 100 mm.
- Wheel Bolt Bore Diameter: 12.6 mm to 12.7 mm. [1, 2, 3]
Factory OEM & Aftermarket Cross-Reference Numbers
Toyota Passo 2018 Shock Absorber
KSh5,000.00 Buy Via WhatsappCore Architectural Specifications (Front Struts)
- Suspension System Layout: Independent MacPherson Strut.
- Internal Shock Mechanics: Gas-Charged Twin-Tube design utilizing low-pressure nitrogen gas to prevent hydraulic fluid cavitation and foaming.
- Strut Assembly Design: Load-bearing structural suspension strut.
- Chassis Platform Application: Third-Generation Toyota Passo (M700A / M710A series).
- Axle Position: Front Axle (Side-specific asymmetrical Left Hand/Right Hand configuration).
- Mounting Pattern: Dual-bolt steering knuckle bottom clamp paired with a threaded top pin chassis tower anchoring profile.
Core Architectural Specifications (Rear Shocks)
- Suspension System Layout: Torsion Beam semi-independent rear suspension axle.
- Damper Assembly Design: Standalone, non-load-bearing Telescopic Shock Absorber (operates entirely separated from the rear coil spring seats).
- Internal Shock Mechanics: Low-pressure gas-charged twin-tube setup.
- Mounting Configuration: Top pin threaded rod mount paired with a bottom eyelet sleeve cross-bolt bushing layout.
- Axle Position: Rear Axle (Symmetrical, interchangeable units for both left and right rear wheel locations).
Drive Train & Chassis Tuning Variations
- 2WD (M700A Chassis) vs. 4WD (M710A Chassis): Rear shock internal valving rates and stroke length profiles are modified distinctly to accommodate the independent differential and extra axle weight distribution on full-time All-Wheel Drive variants.
- Material Composition: Induction-hardened structural steel piston rods enclosed by high-performance multi-lip Nitrile rubber (NBR) fluid seals to resist fine dust ingress.
Factory OEM & Aftermarket Cross-Reference Numbers
- Toyota / Daihatsu Factory Genuine OEM Base Roots:
- KYB (Excel-G OE Replacement Series) Production Catalog Codes:
Subaru Forester SG5 Steering Rack Ex-Japan
KSh10,000.00 Buy Via WhatsappCore Mechanical & Architectural Specifications
- Steering Mechanism Design: Hydraulic Power Assisted Rack and Pinion Steering Gear Assembly.
- Drive Configuration Layout: Engineered strictly for Right-Hand Drive (RHD) Japanese Domestic Market (JDM) chassis profiles.
- Steering Wheel Ratio Responsiveness:
- Standard Cross Sports / XT trims: 3.0 turns lock-to-lock.
- STI Variant (SG9/SG5 specialized upgrade swap): 2.5 turns lock-to-lock (Quick-steer rack configuration).
- Casing Housing Composition: High-strength die-cast Aluminum alloy body with integrated steel mounting sleeve eyelets.
- Tie Rod Thread Metric: M16 x 1.5 inner tie rod housing thread.
- Input Pinion Shaft Splines: 36 Teeth spline profile matching the steering column intermediate U-joint yoke.
Hydraulic Control & Pressure Profiles
- Fluid Compatibility: Dexron II / Dexron III or specialized Subaru Power Steering Fluid (Mineral-based hydraulic oil matrix).
- Maximum Line Operating Pressure: 8.3 to 9.2 MPa (83 to 92 Bar) at maximum pump load.
- Valve Architecture: Internal rotary control valve with dynamic torsion bar feedback to meter hydraulic fluid flow relative to driver steering wheel input speed.
Factory Genuine JDM OEM Cross-Identification
Depending on production dates (Pre-facelift 2002–2005 vs. Facelift 2005–2007) and whether the chassis is a naturally aspirated EJ202 or turbo EJ205, "Ex-Japan" imports pull from these official codes:
- Primary OEM Reference Root Numbers: 34110SA080, 34110SA090, 34110SA110, 34110SA000.
- Aftermarket Parts Blueprint Index:
- Sankei 555 Core Rack Ends: SR-6300.
- Sankei 555 Outer Tie Rod Ends: SE-6301.
Environmental Sealing & Isolation Components
- Fluid Seal Profile: High-durability Nitrile rubber (NBR) dynamic inner shaft seals and dual-lip pinion oil rings.
- Protective Bellows: Heat-treated, oil-resistant Chloroprene rubber (CR) dust boots clamped via spring-steel retention clips to prevent water ingestion into internal gear tracks.
Nissan FB15 Shocks Absorbers Ex-Japan
KSh2,500.00 Buy Via WhatsappCore Architectural Specifications (Front Struts)
-
- Suspension Layout: Independent MacPherson Strut.
- Internal Shock Mechanics: Gas-Charged Twin-Tube low-pressure nitrogen configuration (engineered to eliminate hydraulic fluid aeration on rough road surfaces).
- Strut Assembly Design: Load-bearing structural suspension strut.
- Mounting Configuration: 3-bolt upper triangular tower mounting pattern paired with a bottom dual-bolt steering knuckle mounting bracket.
- Orientation: Asymmetrical, side-specific Left Hand (LH) and Right Hand (RH) directional assemblies.
Core Architectural Specifications (Rear Shocks)
-
- Suspension Layout Compatibility: Multi-Link Beam Axle or rigid trailing link rear suspension setup (depending on standard 2WD or 4WD chassis configurations).
- Shock Assembly Design: Standalone, non-load-bearing Telescopic Shock Absorber (damper operates completely separate from the coil spring seat).
- Mounting Configuration: Top Pin threaded rod connection paired with a Bottom Eyelet sleeve through-bolt bushing.
- Orientation: Symmetrical layout (identical interchangeable units for both Left and Right rear positions).
Chassis & Drive Train Variations (Nissan Sunny FB15 Platform)
-
- 2WD (Front-Wheel Drive) vs. 4WD (FNB15 Chassis): Rear shock dampening rates and internal oil-valving dimensions are split strictly between standard Front-Wheel Drive models and the heavier-duty, higher-load All-Wheel Drive (FNB15 / i-Four) platforms.
- Material Composition: Induction-hardened carbon steel piston rods paired with premium multi-lip Nitrile rubber (NBR) oil seals to survive demanding dust conditions.
Factory OEM & Aftermarket Cross-Reference Numbers
-
- Nissan Genuine Factory JDM OEM Roots:
-
- Front Right Hand (RH): 54302-4M403, 54302-4M425, 54302-WD025
- Front Left Hand (LH): 54303-4M403, 54303-4M425, 54303-WD025
- Rear Axle Dampers: 56210-4M400, 56210-4M425, 56210-4M725
-
- KYB (Excel-G OE Replacement Series) Part Numbers:
-
- Front Right Hand (RH): 333310
- Front Left Hand (LH): 333311
- Rear Axle (Both Sides): 341279
-
- Nissan Genuine Factory JDM OEM Roots:
Nissan March Model K12 Lower Control Arm
KSh4,000.00 Buy Via WhatsappCore Geometric & Material Specifications
- Suspension Type: Track Control Arm / Trailing Wishbone (Independent MacPherson Strut lower pivot locator).
- Material Composition: Stamped Heavy-Duty Structural Sheet Steel.
- Overall Length: 390 mm.
- Overall Width: 375 mm.
- Overall Height: 70 mm.
- Axle Placement: Front Axle (Asymmetrical, side-specific Left/Right configuration). [1, 2, 3, 4]
Pre-Installed Bushing & Joint Data
- Integrated Front Bushing: Cylindrical rubber-to-metal silent block sleeve bushing. [1]
- Integrated Rear Bushing: Heavy-duty rubber damper pad bush.
- Ball Joint Configuration: Integrated press-fit ball joint assembly featuring a 16 mm tapered pin/stud sizing. [1]
Factory Hardware Fastener Torques
- Front Bushing Horizontal Pivot Bolt: 114 Nm (84 ft-lbs).
- Rear Bushing Vertical Pivot Bolt: 108 Nm (80 ft-lbs).
- Ball Joint Knuckle Pinch Bolt: 29 Nm (21 ft-lbs).
- Note on Installation: Fasteners anchoring the inner rubber bushes must only be torqued to final limits once the suspension is pre-loaded to vehicle ride height (approx. 36.5 cm hub-to-fender center) to eliminate binding and premature rubber failure. [1, 2, 3, 4]
Factory Reference & Cross-Identification
- Nissan Genuine OEM Component Part Roots:
- Right Hand (RH): 54500-AX600, 54500-BC40A.
- Left Hand (LH): 54501-AX600, 54501-BC40A.
- Major Aftermarket Technical Cross-References:
Toyota Noah Rear Airmartic
KSh40,000.00 Buy Via WhatsappFactory Architecture & Mechanical Blueprint
- Standard Rear Layout: The factory-standard Toyota Noah (across generations AZR60, ZRR70, ZRR80, and MZRA90) utilizes a Torsion Beam rear suspension system paired with standalone, low-pressure gas-charged shocks and conventional steel coil springs. [1, 2]
- The "Airmatic" Classification: The Toyota Noah does not feature a factory-optioned electronic pneumatic air suspension ("Airmatic") system. When a Noah configuration operates on air bellows, it is utilizing an aftermarket, complete Air Ride Modification / Air Bag Conversion Kit (such as specialized JDM systems by CEIKA Air Ride or custom high-pressure pneumatic double bellows). [1, 2]
Aftermarket Air Bag / Pneumatic Conversion Kit Specifications
For Noah platforms modified with an electronic air sleeve system, the conversion hardware follows these strict mechanical limits:
- Spring Mechanism Replacement: Steel rear coil springs are removed and substituted with High-Pressure Double-Bellows Progressive Rate Air Sleeves. [1]
- Maximum Height Adjustment Range (Stroke): Up to a 125 mm body drop/lift capacity managed dynamically via a dedicated manifold air management computer. [1]
- Damper Compatibility: Tuned to run alongside either threaded, adjustable-length short-stroke performance dampers or factory-specification standalone rear dampers (such as the standard KYB Excel-G 3440109 Series). [1, 2]
- Airbag Operational Pressure Parameters:
Factory Rigid Rear Chassis & Anchoring Points
Whether retaining steel coils or hosting a custom pneumatic bellows block, the core tracking geometry rests on the following factory dimensions:
- Rear Axle Assembly Type: Non-independent trailing-arm layout integrated via a rigid Rear Axle Beam Assembly.
- Shock Mount Interface: Symmetrical standalone Bottom Eyelet sleeve cross-bolts mated directly to the axle carrier arms, paired with isolated upper chassis bushing support assemblies.
- Factory Genuine Rear Damper Part Numbers (For cross-referencing mount clearance): 48530-28560, 48530-80547, 48530-D1010. [1]
Passo 2015 Wheel Hub
KSh4,500.00 Buy Via WhatsappFront Wheel Hub & Bearing Specifications (3rd Gen / KGC30 & NGC30 Series)
- Bearing Style: Generation 1 Press-In Sealed Double-Row Angular Contact Ball Bearing. The standalone driven hub spindle flange presses directly into the front steering knuckle bearing.
- Integrated Sensor Technology: Features a magnetic multi-pole ABS encoder ring built directly into one side of the inner oil seal face.
- Axle Location: Front Axle (Symmetric Left / Right configuration).
- Front Bearing Core Dimensions: Inner Diameter: 38.0 mm | Outer Diameter: 70.0 mm | Width / Thickness: 37.0 mm.
- Wheel Lug Pattern Configuration: 4 Holes.
- Pitch Circle Diameter (PCD): 4 x 100 mm.
- Centering / Hub Pilot Outer Diameter: 54.0 mm.
- Internal Drive Splines: 24 Internal Teeth on the hub center (interfacing with the outer CV joint axle stub).
- Genuine Toyota/Daihatsu OEM Part Numbers: 43560-B1010, 43550-B1010 (Hub bearing assembly unit), 43510-B1011 (Hub axle component).
- Major Aftermarket Cross-References: NSK 38BWD26, GMB GH32560, Koyo DAC38700037, Febest DAC38700037M-KIT.
Rear Wheel Hub & Bearing Unit Specifications (2WD Models)
- Design Configuration: Generation 3 Modular, Unitized Bolt-On Rear Hub Assembly. The wheel hub flange, dual-row inner tracks, outer casing, and magnetic ABS target mechanics are integrated into a single, non-serviceable sealed module.
- Axle Position: Rear Axle (Symmetric Left / Right mounting geometry).
- Wheel Lug Arrangement: 4 Holes.
- Rear Pitch Circle Diameter (PCD): 4 x 100 mm.
- Centering / Brake Drum Pilot Diameter: 54.0 mm.
- Mounting Flange Layout: 4-Bolt Rectangular Pattern matching to the rear trailing arm axle plate.
- ABS Signal Integration: Pre-assembled internal multi-pole magnetic target track enclosed within the spindle sealing cap face.
- Material Composition: Precision induction-hardened GCr15 High-Carbon Chromium Bearing Steel internals matched with a 55# structural forged steel hub casing.
- Genuine Toyota/Daihatsu OEM Part Numbers (Rear): 42450-B1020, 42410-B1020.
- Major Aftermarket Cross-References (Rear): GMB GH32630, Koyo 3DACF026F-23HS-AM, FAG 713621210.
Daihatsu Mira Wheel Hub
KSh4,000.00 Buy Via WhatsappFront Wheel Hub & Bearing Specifications (Modern JDM Layout / L275 & LA300 Series)
- Bearing Style: Generation 1 Press-In Sealed Double-Row Angular Contact Ball Bearing. The standalone driven hub flange presses into the steering knuckle-seated bearing.
- Integrated Sensor Technology: Features a magnetic multi-pole ABS encoder ring built directly into the rubber oil seal face on one side of the bearing.
- Axle Location: Front Axle (Symmetric Left / Right configuration).
- Front Bearing Core Dimensions: Inner Diameter: 35.0 mm | Outer Diameter: 64.0 mm | Width / Thickness: 37.0 mm.
- Wheel Lug Pattern Configuration: 4 Holes.
- Pitch Circle Diameter (PCD): 4 x 100 mm (Modern series standard, replacing the legacy 4x110 mm vintage configurations).
- Centering / Hub Pilot Outer Diameter: 54.0 mm.
- Genuine Daihatsu Genuine OEM Part Numbers: 43560-B2020, 43560-B2021, 43560-B2030.
- Major Aftermarket Cross-References: DAC35640037M (Industry Standard Blueprint), FEBI 172477, GSP 9400087. [1, 2, 3, 4, 5, 6]
Rear Wheel Hub & Bearing Unit Specifications (2WD Models)
- Design Configuration: Generation 3 Modular, Unitized Bolt-On Rear Hub Assembly. The wheel hub flange, dual-row inner ball tracks, outer casing, and ABS target mechanics are integrated into a single, non-serviceable sealed module.
- Axle Position: Rear Axle (Symmetric Left / Right mounting geometry).
- Wheel Lug Arrangement: 4 Holes.
- Rear Pitch Circle Diameter (PCD): 4 x 100 mm.
- Mounting Flange Layout: 4-Bolt Rectangular Pattern matching to the rear trailing arm/torsion beam drop axle base.
- Mounting Bore Distance: 72.0 mm.
- ABS Signal Integration: Pre-assembled active ABS sensor ring or multi-pole target track containing a 96-magnetic-pole layout.
- Material Composition: Precision induction-hardened GCr15 High-Carbon Chromium Bearing Steel internals matched with a 55# structural forged steel hub casing.
- Genuine Daihatsu OEM Part Roots: 42450-B2010, 42450-B2050, 42450-B2060. [1, 2, 3, 4, 5]
Mitsubishi Mirage Wheel Hub
KSh5,000.00 Buy Via WhatsappFront Wheel Hub & Bearing Specifications (6th Generation / LA Chassis)
- Bearing Style: Generation 1 Press-In Sealed Double-Row Angular Contact Ball Bearing. The bearing presses directly into the front steering knuckle, and the standalone driven hub spindle flange presses into the bearing's inner race.
- Integrated Sensor Technology: Features a magnetic ABS sensor encoder ring integrated directly into the rubber oil seal face on one side of the bearing.
- Axle Location: Front Axle (Symmetric Left / Right configuration).
- Outer Hub Flange Diameter: 120.0 mm.
- Wheel Lug Pattern Configuration: 4 Holes.
- Pitch Circle Diameter (PCD): 4 x 100 mm.
- Centering / Hub Pilot Outer Diameter: 56.0 mm.
- Internal Drive Splines: 25 Internal Teeth on the hub center (interfacing with the outer CV joint axle stub).
- Front Bearing Core Dimensions: Inner Diameter: 38.0 mm | Outer Diameter: 70.0 mm | Width / Thickness: 37.0 mm.
- Genuine Mitsubishi OEM Part Numbers: 3880A024 (Front Bearing), 3885A017 / 3885A040 (Front Hub Flange Spindle).
- Major Aftermarket Cross-References: NSK 38BWD26, GMB GH32710, Febest DAC38700037-KIT.
Rear Wheel Hub & Bearing Unit Specifications (2WD Models)
- Design Configuration: Generation 3 Modular, Unitized Bolt-On Rear Hub Assembly. The wheel hub, dual-row bearing tracks, outer flange, and ABS tone ring are pre-assembled into a single, non-serviceable sealed unit that bolts straight to the rear trailing arm axle beam.
- Axle Position: Rear Axle (Symmetric Left / Right mounting geometry).
- Wheel Lug Arrangement: 4 Holes.
- Rear Pitch Circle Diameter (PCD): 4 x 100 mm.
- Centering / Brake Drum Pilot Diameter: 56.0 mm.
- Mounting Flange Configuration: 4-Bolt Trapezoidal Pattern mounting to the rear axle.
- ABS Target Integration: Internal magnetic multi-pole tone ring enclosed within the spindle sealing cap face.
- Material Composition: Induction-hardened GCr15 High-Carbon Chromium Bearing Steel internals matched with a 55# structural forged steel outer hub casing.
- Genuine Mitsubishi OEM Part Numbers (Rear): 3785A015, 3785A035.
- Major Aftermarket Cross-References (Rear): GMB GH33120, NTN HUB319T-1, FAG 713619930.
Suzuki Alto 2015 Wheel Hub
KSh4,000.00 Buy Via WhatsappFront Wheel Hub & Bearing Specifications (7th Generation / HA36 Series)
- Design Layout: Combined Generation 1 Press-In double-row angular contact sealed ball bearing pressed into a standalone forged hub flange.
- Integrated Sensor Technology: Features a magnetic ABS sensor encoder ring built directly into the inner oil seal face (must be pressed in facing inward toward the knuckles).
- Axle Location: Front Axle (Left / Right symmetric configuration).
- Outer Hub Flange Diameter: 114.0 mm.
- Wheel Lug Pattern Configuration: 4 Holes.
- Pitch Circle Diameter (PCD): 4 x 100 mm.
- Centering / Hub Pilot Outer Diameter: 54.0 mm.
- Internal Drive Splines: 23 Internal Teeth (on standard 2WD HA36S variants) or 24 Internal Teeth (on specialized 4WD or Turbo RS/Worko HA36S variants).
- Genuine Suzuki OEM Numbers: 43401-74P00, 43401-74P01, 43401-50M00 (Bearing kit: 43440-50M00, 43440-74P00).
- Major Aftermarket Cross-References: NSK 35BWD28, GMB GH33030, JIKIU HW22026.
Rear Wheel Hub & Bearing Specifications (Integrated Rear Drum Layout)
- Design Configuration: Built directly into the Rear Brake Drum assembly (Generation 1 sealed press-in bearing integrated directly inside the brake drum cavity, turning on a non-driven spindle shaft).
- Axle Position: Rear Axle (Symmetric Left / Right mounting geometry).
- Wheel Lug Arrangement: 4 Holes.
- Rear Pitch Circle Diameter (PCD): 4 x 100 mm.
- Inner Hub Bearing Bore Steps: Inner Diameter: 25.0 mm | Outer Diameter: 52.0 mm | Height/Thickness: 43.0 mm.
- Material Composition: Forged grey alloy iron drum base matching induction-hardened GCr15 High-Carbon Chromium Bearing Steel internals.
- Genuine Suzuki OEM Numbers (Rear): 43511-74P00, 43511-50M10, 43511-68K00 (Bearing component: 46860-50M00).
- Major Aftermarket Cross-References (Rear): Koyo DAC25520043, Febest DAC25520043-KIT.
Toyota Wish Steering Rack Ex-Japan
KSh16,000.00 Buy Via WhatsappCore Mechanical & Architectural Specifications
- Steering Mechanism Design: Column-assist Electric Power Steering (EPS) or conventional Hydraulic Rack and Pinion.
- Drive Configuration Layout: Configured specifically for Right-Hand Drive (RHD) Japanese Domestic Market (JDM) vehicle applications.
- Steering Responsiveness: 2.88 turns lock-to-lock (total steering wheel rotations).
- Net Gear Assembly Weight: 6.6 kg (bare structural unit weight).
- Casing Housing Material: Induction-hardened cast Aluminum alloy matched with high-tensile structural steel tie rods.
- Tie Rod Thread Metric: M16 x 1.5 or M14 depending on target generation tie rod seating.
- Internal Gear Mechanics: Helical gear teeth configuration cut directly onto an internal NSK-manufactured steel rack bar. [1, 2, 3, 4, 5]
Generation-Specific Engineering Variations
The steering rack engineering for an "Ex-Japan" Toyota Wish splits completely by vehicle generation profile:
1. First Generation: X10 Platform (2003–2009) — ZNE10G (1.8L 1ZZ-FE) / ANE10G (2.0L 1AZ-FSE)
- Assist Technology Type: Primarily equipped with low-stress Manual/Mechanical rack setups linked to a column-mounted EPS electric drive motor.
- Primary OEM Part References: 45510-68010, 45510-68011.
- Tie Rod / Rack End Code: 45503-29825. [1, 2, 3, 4]
2. Second Generation: X20 Platform (2009–2017) — ZGE20G / ZGE21G (2ZR-FAE / 3ZR-FAE)
- Assist Technology Type: Specialized Electric Power Steering (EPS) integrated system housing rigid, vibration-damping tie rod guide sleeves.
- Primary OEM Part References: 45510-68020, 45510-68021, 45510-68030, 45510-68041. [1, 2, 3]
Fluid & Environmental Protection Seals
- Sealing Gaskets: Weatherproof and ozone-resistant synthetic Chloroprene rubber (CR) bellows/boots secured by dynamic steel retention bands. [1]
- Lubrication Interface: Factory-packed with low-friction, high-viscosity synthetic lithium soap grease to prevent internal track teeth damage.
Harrier 240 Steering Rack Ex-Japan
KSh20,000.00 Buy Via WhatsappCore Architectural & Mechanical Specifications
- Steering Mechanism Design: Hydraulic Power Assisted Rack and Pinion Steering Gear Assembly.
- Drive Configuration Layout: Engineered strictly for Right-Hand Drive (RHD) Japanese Domestic Market (JDM) chassis profiles.
- Steering Wheel Responsiveness: 2.88 turns lock-to-lock (total steering wheel rotations).
- Net Gear Weight (Bare Assembly): 6.6 kg.
- Casing/Housing Composition: High-strength cast Aluminum alloy integrated with specialized iron sleeve structural sleeves.
- Tie Rod / Thread Sizing: M16 x 1.5 inner tie rod thread metric. [1, 2, 3, 4, 5]
Chassis Generation-Specific Compatibility
The "Harrier 240" designation indicates models running the 2.4L 2AZ-FE inline-4 engine. The steering rack specifications split cleanly into two distinct generations: [1, 2]
1. First Generation: X10 Platform (1997–2003) — ACU10 (2WD) / ACU15 (4WD)
- Assist Technology Type: Standard high-pressure conventional hydraulic system.
- Primary OEM Part References: 44250-48010, 44250-48080, 44200-48031.
- Interchangeability: Directly cross-compatible with the Lexus RX300 (MCU10 series) and the Toyota Kluger V platform of identical production years. [1, 2, 3, 4, 5]
2. Second Generation: X30 Platform (2003–2013) — ACU30W (2WD) / ACU35W (4WD)
- Assist Technology Type: Low-mounted proportional-flow hydraulic system configured for enhanced high-speed stabilization.
- Primary OEM Part References: 44200-48080, 44200-48150, 40120-48080.
- Interchangeability: Shared architecture directly swappable with the second-generation Lexus RX330, RX350, and MCU30-series Toyota Harrier assemblies. [1, 2]
Ex-Japan Inspection Standards & Seals
- Fluid Seal Profile: Highly dynamic, heat-resistant Nitrile rubber (NBR) triple-lip seals engineered to withstand hydraulic fluid line pressures upwards of 8.0–9.0 MPa.
- OEM Valve Integration: Features an integrated internal rotary control valve to mechanically meter fluid assist based on twist torque from the intermediate steering column shaft.
Volkswagen Golf Shocks Absorbers Ex German
KSh4,500.00 Buy Via WhatsappCore Architectural Specifications (Front Struts)
- Suspension Layout: Independent MacPherson Strut.
- Internal Shock Mechanics: Gas-Pressure Twin-Tube system (low-pressure nitrogen gas charged to eliminate hydraulic fluid aeration and foaming). [1, 2]
- Strut Assembly Design: Load-bearing structural suspension strut. [1, 2]
- Housing/Clamping Area Outer Diameter: 50 mm or 55 mm base outer diameter variants (critical configuration check for standard vs. sports/heavy-duty chassis platforms). [1, 2]
- Mounting Pattern: Bottom Plate clamping housing paired with a threaded top pin chassis tower anchoring profile. [1]
Core Architectural Specifications (Rear Dampers)
- Suspension Layout Compatibility: Multi-Link independent axle or rigid Twist-Beam configuration variants.
- Shock Assembly Design: Standalone non-load-bearing Telescopic Shock Absorber (damper operates completely separate from the independent coil spring seat).
- Internal Shock Mechanics: Gas-pressure twin-tube setup.
- Mounting Configuration: Bottom eye housing sleeve cross-bolt paired with a threaded top pin bushing adapter. [1, 2, 3]
Factory OEM & German Aftermarket Component Identification
- Primary Factory Reference Roots:
- Premium German OE Vendor Configurations (Ex-German / New Alternates):
- Bilstein (B4 OE Replacement series): 22-131607 (Front), 19-127439 (Rear), 23-238978 (DampTronic electronic control front).
- Sachs / Lemförder Matrix: 317 330 (Front Axle), 315 910 (Front alternate), 315 912 (Rear Axle).
- Febi Bilstein Baseline Profile: 193134 (Front strut assembly). [1, 2, 3, 4, 5, 6]
Subaru Impreza GP2 Shock Mountain
KSh3,500.00 Buy Via WhatsappFront Strut Top Mount Specifications
-
- Mounting Configuration: 3-bolt upper triangular tower mounting footprint.
- Chassis Isolator Construction: Heavy-duty vulcanized shore-hardness rubber chemically bonded to a stamped structural steel core casing.
- Integrated Bearing Profile: Heavy-duty internal axial thrust ball bearing mechanism integrated within the rubber seat to facilitate smooth, unbinding rotation of the MacPherson strut during steering inputs.
- Axle Symmetry: Symmetrical, non-directional layout (same component services both the Front Left Hand and Front Right Hand strut assemblies).
- Subaru Factory Genuine OEM Part Numbers: 20320FG012, 20320FG013, 20320FG002.
- Factory Hardware Installation Torques:
-
- Chassis Tower Flange Nuts (3 per mount): 20 Nm (14.5 ft-lbs).
- Center Piston Rod Strut Nut: 55 Nm (41 ft-lbs).
-
Rear Shock Top Mount Specifications
- Mounting Configuration: Dual-bolt (2-bolt) linear top-hat pin configuration.
- Suspension Architecture Match: Specifically configured for the independent multi-link rear suspension platform utilized on the GP2 chassis.
- Isolator Type: Isolated thick-sandwich rubber bushing damper configuration designed to suppress high-frequency road vibrations and Cabin NVH (Noise, Vibration, and Harshness).
- Subaru Factory Genuine OEM Part Numbers: 20370FG012, 20370FJ001.
- Factory Hardware Installation Torques:
- Upper Chassis Fasteners (2 per mount): 30 Nm (22 ft-lbs).
- Center Damper Shaft Retaining Nut: 25 Nm (18.4 ft-lbs).
Subaru Outback Model BP5 Bilstain Shocks
KSh8,000.00 Buy Via WhatsappFront Axle Bilstein Strut Specifications
- Suspension Layout: Independent MacPherson Strut.
- Internal Shock Architecture: Inverted Monotube (Upside-Down Technology). The piston rod is integrated inside the bottom axle casing, while the thicker outer tube acts as the structural slider. This drastically increases lateral rigidity under heavy cornering loads. [1]
- Damping Medium: High-pressure nitrogen gas with a single-tube hydraulic fluid separation piston. [1]
- Mounting Configuration: 3-bolt top pin hat assembly with a lower dual-bolt steering knuckle clamp layout. [1]
- Damping Forces (Measured @ 0.52 m/s):
- Compression Force: 1090 N
- Rebound Force: 2460 N [1]
- Orientation: Asymmetrical, side-specific left and right structures.
Rear Axle Bilstein Shock Specifications
- Suspension Layout: Multi-Link Independent Rear Suspension.
- Internal Shock Architecture: Standard Monotube (Gas Pressure).
- Shock Design Type: Non-load-bearing telescopic damper (does not carry a spring seat; operates independently of the rear coil spring).
- Lower Bushing Bushing Assembly OD: 40 mm (Specific to the BP/BL platform; thicker than later generation models).
- Mounting Connections: Top Pin threaded rod | Bottom Eyelet sleeve through-bolt bushing. [1, 2, 3]
Factory OEM & Aftermarket Part Numbers
- Bilstein Aftermarket Performance Upgrade (B6 Heavy Duty Series):
- Subaru Factory Genuine JDM OEM Numbers (Spec.B Baseline):
- Front Right Hand (RH): 20310AG401, 20310AG424, 20310AG100
- Front Left Hand (LH): 20310AG411, 20310AG434
- Rear Axle Dampers: 20365AG274
Honda fit, Honda insight, Honda fit shuttle Wheel Hub Bearing
KSh5,000.00 Buy Via WhatsappFront Wheel Bearing Specifications (Press-In Sealed Type)
The front axle uses a Generation 1 sealed double-row angular contact ball bearing that must be pressed into the front steering knuckle assembly. [1, 2]
-
- Inner Diameter (ID): 43 mm
- Outer Diameter (OD): 79 mm
- Inner Ring Width: 41 mm
- Outer Ring Width: 38 mm
- ABS Integration: Features an integrated 96-magnetic-pole ABS encoder ring built directly into one side of the inner oil seal face (the bearing must be pressed in with this magnetic side facing inward toward the sensor).
- Honda Factory Genuine OEM Part Numbers: 44300-TF0-951, 44300-SCC-003, 44300-SEY-008, 44300-T5A-951.
- Major Aftermarket Cross-References: NSK 43BWD14, Febest DAC43793841M, SKF FW36. [1, 2, 3, 4, 5]
Rear Wheel Hub Bearing Unit Specifications (2WD Models)
For standard Front-Wheel Drive (2WD) models, the rear bearing is built into a non-serviceable, sealed Generation 3 complete modular bolt-on hub assembly that slides over a spindle stub axle and is secured by a single central axle nut. [1, 2]
-
- Wheel Stud Quantity: 4 Studs
- Pitch Circle Diameter (PCD / Lug Bolt Pattern): 4 x 100 mm
- Flange Outer Diameter: 151.8 mm
- Brake Pilot / Center Bore Diameter: 56.1 mm
- Wheel Pilot Diameter: 51.0 mm
- ABS Integration: Includes a pre-assembled, internal multi-pole magnetic ABS tone wheel tracking layout integrated on the spindle-facing side.
- Honda Factory Genuine OEM Part Numbers: 42200-TF0-Z51, 42200-TF6-951, 42200-TG0-T51.
- Major Aftermarket Cross-References: PFI PHU2323, Industry Standard Ref 512323. [1, 2, 3, 4, 5, 6]
Material Composition & Structural Tolerances
- Steel Grade: Precision-hardened GCr15 High-Carbon Chromium Bearing Steel used across inner/outer structural tracks and internal rolling elements for high heat dissipation and fatigue resistance.
- Flange Hardness: 55# structural forged medium-carbon steel base casing to withstand extreme cornering shear loads.
- Lubrication: Pre-packed, life-lubricated high-performance polyurea synthetic grease optimized for operating ranges from -20°C to 120°C.
Mazda Premacy 4WD Wheel Hub Bearing
KSh7,000.00 Buy Via WhatsappFront Wheel Bearing Specifications (Press-In Angular Contact Type)
- Inner Diameter (ID): 42 mm (Standard on later iterations like CR/CW chassis) or 40 mm (Early CP chassis iterations).
- Outer Diameter (OD): 80 mm (Later models) / 74 mm (Early CP models).
- Width / Thickness: 45 mm (Later models) / 40 mm (Early CP models).
- Bearing Construction: Double-row sealed angular contact ball bearing.
- ABS Integration: Features a magnetic multi-pole ABS encoder ring built directly into the integrated inner oil seal rubber lip face.
- Front Spline Layout: 31 Internal Hub Spline Teeth interfacing with the outer CV joint shaft axle stub. [1, 2, 3, 4]
Rear Wheel Hub & Bearing Specifications (4WD / AWD Assembly)
- Design Configuration: Generation 3 modular, complete bolt-on rear wheel hub assembly unit. Unlike 2WD variants, the 4WD version features a hollow splined center to accept a rear drive shaft. [1]
- Axle Position: Rear Axle (Symmetric Left / Right mounting geometry). [1]
- Flange Outer Diameter: 140 mm. [1]
- Wheel Lug Pattern Pattern: 5 Holes. [1]
- Pitch Circle Diameter (PCD): 5 x 114.3 mm (Standard Mazda medium-wagon layout).
- ABS Sensor Profile: 44 Teeth passive tone wheel window or specialized integrated internal magnetic pole ring depending on chassis year (CP vs. CWEAW). [1, 2]
- Material Composition: Forged 55# structural steel housing flanges structurally mated with precision induction-hardened GCr15 high-carbon chromium bearing steel tracks.
Factory Reference & Cross-Identification Numbers
Mazda Demio 2017 Wheel Hub Bearing
KSh7,000.00 Buy Via WhatsappFront Wheel Hub & Bearing Specifications (Gen 4 / DJ Chassis)
-
- Bearing Style: Press-In Generation 1 Generation/Design Sealed Angular Contact Double-Row Ball Bearing.
- Integrated Sensor Technology: Features a magnetic ABS sensor encoder ring built directly into the inner oil seal face.
- Axle Location: Front Axle (Left / Right symmetric configuration).
- Outer Hub Flange Diameter: 122.0 mm to 122.8 mm.
- Wheel Lug Pattern Configuration: 4 Holes.
- Pitch Circle Diameter (PCD): 4 x 100 mm.
- Genuine Mazda OEM Numbers: D09H-33-04XA, DA7H-33-04XA.
- Major Aftermarket Cross-Reference Cataloging: FAG 713 6280 40, OPTIMAL 942108, ESEN SKV 29SKV431. [1, 2, 3, 4, 5, 6]
Rear Wheel Hub Bearing Unit Specifications
- Chassis Configurations:
- 2WD Wheel Lug Arrangement: 4 Holes. [1]
- Rear Hub Pitch Circle Diameter (PCD): 4 x 100 mm. [1]
- ABS Sensor Profile: 88 Teeth / Magnetic Pole Lines embedded inside the rear dust-shield interface. [1]
- Material Composition: High-grade GCr15 High-Carbon Chromium Bearing Steel (hardened internal races and rolling ball tracks) enclosed by 55# structural forged steel casing components.
- Rear Hub Aftermarket Cross-References: MEYLE 714 752 0003, ABAKUS 132-02-044.
Showing 224 of 641 results



























