Sort

Toyota Passo Model 2015 Engine Mountain

KSh4,000.00
Engine & Performance Specifications
    • Engine Model: 1KR-FE (Alternatively available with the 1.3L 1NR-FE)
    • Displacement: 996 cc (1.0 Litre)
    • Cylinder Configuration: Inline 3-cylinder, 12-Valve
    • Valvetrain: DOHC (Double Overhead Camshaft)
    • Bore × Stroke: 71.0 mm × 83.9 mm
    • Compression Ratio: 11.5:1 (Upgraded in 2014 for higher thermal efficiency)
    • Maximum Power Output: 69 PS (51 kW) @ 6,000 RPM
    • Maximum Torque: 92 N·m (9.4 kg·m) @ 4,400 RPM [1, 2, 3, 4, 5, 6]
Drivetrain & Transmission
    • Transmission Type: Continuously Variable Transmission (CVT) [1, 2]
    • Drive System Configurations:
        • 2WD / Front-Wheel Drive (Chassis Model: KGC30)
        • 4WD / All-Wheel Drive (Chassis Model: KGC35) [1, 2, 3]
Engine Mounting Setup (Physical Mounts)
  • Mounting Configuration: 3-Point Insulator Isolation Setup [1]
  • Right-Hand (RH) Mount: Hydraulic (Fluid-filled) Insulator assembly to absorb 3-cylinder engine idling vibrations (OEM Base Part No: 12305). [1, 2]
  • Left-Hand (LH) Mount: Transmission-side rubber insulator bracket assembly (OEM Base Part No: 12306). [1]
  • Rear (RR) Mount: Engine moving control rod/rear structural engine stay to limit longitudinal engine twisting during acceleration (OEM Base Part No: 12380 / 12309). [1]

Toyota Passo Model 2018 Engine Mountain

KSh4,000.00
Engine & Performance Specifications
  • Engine Model: 1KR-FE
  • Displacement: 996 cc (1.0 Litre)
  • Cylinder Configuration: Inline 3-cylinder, 4-cycle
  • Valvetrain: DOHC (Double Overhead Camshaft)
  • Bore × Stroke: 71.0 mm × 83.9 mm
  • Maximum Power Output: 69 PS (51 kW) @ 6,000 RPM
  • Maximum Torque: 92 N·m (9.4 kg·m) @ 4,400 RPM
  • Fuel Type: Petrol [1, 2, 3, 4, 5, 6]
Drivetrain & Transmission
  • Transmission Type: Continuously Variable Transmission (CVT) [1, 2]
  • Drive System Options:
    • 2WD / Front-Wheel Drive (Chassis Model: M700A)
    • 4WD / All-Wheel Drive (Chassis Model: M710A) [1, 2, 3]
Fuel & Capacity
  • Fuel Tank Capacity: 36 to 38 Litres
  • Average Fuel Efficiency: Approximately 20.0 km/L to 24.0 km/L depending on driving conditions

Toyota fielder Model 2015-2010 Lower Control Arms

KSh4,000.00
Toyota Corolla Fielder (2010–2015) Lower Control Arm Technical Specifications
The Toyota Corolla Fielder spanning the 2010–2015 timeline transitions across two structural generations: the Late E140 Series (2010–2012) and the Early E160 Series (2012–2015). Both generations utilize an L-shaped MacPherson strut lower wishbone arm matrix, but they feature distinct factory part configurations and physical bushing dimensions. [1, 2, 3, 4]
1. E140 Series Fielder (2010–2012 Production)
  • Chassis System Codes: NZE141G, NZE144G (4WD), ZRE142G, ZRE144G (4WD) [1]
  • Right Hand (RH) Control Arm OEM: 48068-12300 / 48068-12290 [1, 2]
  • Left Hand (LH) Control Arm OEM: 48069-12300 / 48069-12290 [1, 2]
  • Dimensional Parameters & Bushings:
    • Forward Pivot Bolt Sleeve ID: 14.2 mm
    • Rear Large Bushing Outer Diameter (OD): 65.2 mm
    • Bushing Component Component Refs: Small Front Bushing (48654-12150 / RU-494); Large Rear Bushing (48655-12120 / RU-495 / TAB-145).
2. E160 Series Fielder (2012–2015 Production)
  • Chassis System Codes: NZE161G, NZE164G (4WD), NRE161G, NKE165G (Hybrid Wagon) [1, 2]
  • Right Hand (RH) Control Arm OEM: 48068-59135 / 48068-59145 [1, 2]
  • Left Hand (LH) Control Arm OEM: 48069-59135 / 48069-59145 [1, 2]
  • Bushing Configuration Specs:
    • Features a redesigned low-profile stamped frame geometry to decrease vehicle curb weight on the E160 platform.
    • Pressed Elastomeric Bushing Ref: RU-519 (Masuma tracking variant).
    • Ball Joint Compatibility Ref: MB-3602 (Features specialized dust boot configuration MO-2112). [1, 2]
3. Engineering Material & Layout Layout Specs
  • Structural Frame Shell: Robotic-welded heavy-gauge stamped carbon steel sheet matrix. [1]
  • Pivot Configuration: 3-Point multi-axis movement tracking (Inner front horizontal rubber bush, inner rear vertical trailing bush, and outer ball joint knuckle receptacle). [1]
  • Drivetrain Variance (2WD vs 4WD): 4WD platforms (NZE144G / NZE164G) utilize alternative bushing durometer tolerances along the inner sleeves to absorb transfer-case counter-shudder, despite sharing spatial geometries with FWD counterparts.[1, 2]

Toyota Nze Lower Control Arms

KSh4,000.00
Toyota Corolla NZE Series Front Lower Control Arm Technical Specifications
The front lower control arms for the Toyota Corolla NZE series (predominantly the NZE121 and NZE141 chassis generations, matching the 1.5L 1NZ-FE platform) utilize a conventional L-shaped MacPherson strut lower wishbone architecture. This assembly establishes a structural connection between the lower steering knuckle and the vehicle’s main engine subframe crossmember. [1, 2, 3]
1. E120 Generation NZE Series (Production 2000–2006)
  • Chassis Codes Covered: NZE121, ZZE122, CZE121 [1, 2]
  • Right Hand (RH) Front Lower Control Arm OE: 48068-20400 / 48068-12220 [1, 2]
  • Left Hand (LH) Front Lower Control Arm OE: 48069-20400 / 48069-12220 [1, 2]
  • Structural Material: Stamped structural carbon sheet steel. [1, 2]
  • Bushing Internal Steel Sleeve Dimensions:
    • Forward Horizontal Pivot Sleeve (Inner Diameter): 14.2 mm (Matches M14 alignment fasteners).
    • Rear Vertical Trailing Bush Sleeve (Inner Diameter): 14.5 mm
  • Pressed Elastomeric Sub-Components:
    • Small Front Bushing Ref: 48654-12120 / RU-357 (Dimensions: 14.2mm ID × 39.0mm OD × 59.0mm Length)
    • Large Rear Bushing Ref: 48655-12170 / RU-385 / TAB-026 (Dimensions: 14.5mm ID × 68.5mm OD × 60.0mm Length) [1]
  • Platform Sharing / Cross-Compatibility: Interchanges directly with the Toyota Allion/Premio (240 series), Toyota Wish (10 series), and the Toyota Matrix (ZZE130). [1, 2]
2. E140 Generation NZE Series (Production 2007–2012)
  • Chassis Codes Covered: NZE141 (Axio / Fielder variants) [1, 2]
  • Right Hand (RH) Front Lower Control Arm OE: 48068-12300 / 48068-12290 [1, 2]
  • Left Hand (LH) Front Lower Control Arm OE: 48069-12300 / 48069-12290 [1]
  • Component Weight: Approximately 3.15 kg per side assembly.
  • Bushing Internal Steel Sleeve Dimensions:
    • Forward Horizontal Pivot Sleeve (Inner Diameter): 14.2 mm
    • Rear Vertical Trailing Bush Sleeve (Inner Diameter): 14.4 mm
  • Pressed Elastomeric Sub-Components:
    • Small Front Bushing Ref: 48654-12150 / RU-494 (Dimensions: 14.2mm ID × 38.2mm OD × 61.0mm Length)
    • Large Rear Bushing Ref: 48655-12120 / RU-495 / TAB-145 (Dimensions: 14.4mm ID × 65.2mm OD × 55.0mm Length)
3. Structural Alignment & Geometry Overview
  • Mounting Interface Layout: 3-Point multi-axis tracking (Inner forward horizontal bushing + Inner rear vertical bush + Outer steering knuckle ball joint receiver flange).
  • Elastomeric Compound Type: High-durometer vulcanized natural rubber (NR) bonded inside steel backing sleeves. [1, 2, 3]

Toyota Axio Model 2007-2012 Lower Control Arms

KSh4,000.00
Toyota Corolla Axio (2007–2012) Lower Control Arm Technical Specifications
The front lower control arms for the E140 generation Toyota Corolla Axio (chassis codes: NZE141, NZE144 [4WD], ZRE142, ZRE144 [4WD], production range 2007–2012) feature a conventional L-shaped MacPherson strut lower wishbone architecture. This assembly structurally joins the lower steering knuckle to the vehicle's engine crossmember subframe.
1. Core Part Identification & OEM Numbers
  • Right Hand (RH) Front Lower Control Arm:
    • 48068-12300 (Primary factory baseline number)
    • Interchangeable Structural Refs: 48068-02140, 48068-12290, 48068-02160
  • Left Hand (LH) Front Lower Control Arm:
    • 48069-12300
    • Interchangeable Structural Refs: 48069-02140, 48069-12290, 48069-02160
  • Component Weight: Approximately 3.15 kg per side (complete stamped shell assembly with bushings pressed).
2. Dimensional & Physical Parameters
  • Structural Frame Material: Stamped heavy-gauge cold-rolled structural carbon steel plate.
  • Chassis Attachment Layout: 3-Point orientation (Inner forward horizontal bushing + Inner rear vertical trailing bushing + Outer steering knuckle ball joint receiver flange).
  • Bushing Internal Steel Sleeve Dimensions:
    • Forward Horizontal Bolt Sleeve (Inner Diameter): 14.2 mm (Engineered to receive an M14 pivot bolt)
    • Rear Vertical Trailing Bush Sleeve (Inner Diameter): 14.4 mm
  • Rear Large Bushing Outer Barrel Diameter (OD): 65.2 mm
  • Rear Large Bushing Metal Casing Height: 55.0 mm
3. Elastomeric Component & Bushing Specifications
  • Material Compound: High-durometer vulcanized natural rubber (NR) bonded inside carbon steel inner and outer backing sleeves.
  • Bushing Sub-Components (For Independent Pressing/Rebuilds):
    • Small Front Bushing Ref: 48654-12150 / RU-494 (Dimensions: 14.2mm ID × 38.2mm OD × 61.0mm Length)
    • Large Rear Bushing Ref: 48655-12120 / RU-495 / TAB-145 (Dimensions: 14.4mm ID × 65.2mm OD × 55.0mm Length)
4. Drivetrain & Platform Cross-Compatibility
  • 2WD vs. 4WD Architecture: 2WD models (NZE141, ZRE142) share identical base control arms. 4WD models (NZE144, ZRE144) utilize alternative rear bushing durometers to mitigate drivetrain twist from the transfer case, though the physical arm geometry remains interchangeable.
  • Platform Sharing: The E140 Axio lower control arm shares an identical structural chassis footprint with the Toyota Corolla Fielder (E140), Toyota Auris (E150), and Toyota Blade (E150) variations of the same production era.

Toyota Allion 240 Lower Control Arms

KSh4,000.00
Toyota Allion 240 Series Lower Control Arm Technical Specifications
The front lower control arms for the first-generation Toyota Allion 240 series (chassis codes: NZT240, ZZT240, AZT240, ZZT245 [4WD], production range 2001–2007) utilize an L-shaped MacPherson strut lower wishbone architecture. This assembly structurally joins the front steering knuckle to the main engine crossmember subframe.
1. Core Part Identification & OEM Numbers
  • Right Hand (RH) Front Lower Control Arm:
    • 48068-20400 (Primary factory baseline number)
    • Interchangeable Structural Refs: 48068-02050, 48068-12220, 48068-0M010
  • Left Hand (LH) Front Lower Control Arm:
    • 48069-20400
    • Interchangeable Structural Refs: 48069-02050, 48069-12220, 48069-0M010
  • Component Weight: Approximately 3.39 kg per side (complete stamped assembly with bushings pressed).
2. Dimensional & Physical Parameters
  • Structural Frame Material: Stamped heavy-gauge cold-rolled carbon sheet steel.
  • Chassis Attachment Layout: 3-Point orientation (Inner forward horizontal bushing + Inner rear vertical trailing bushing + Outer steering knuckle ball joint receiver).
  • Bushing Internal Steel Sleeve Dimensions:
    • Forward Horizontal Bolt Sleeve (Inner Diameter): 14.2 mm (Engineered for an M14 pivot bolt)
    • Rear Vertical Trailing Bush Sleeve (Inner Diameter): 14.5 mm
  • Rear Large Bushing Outer Barrel Diameter (OD): 68.5 mm
  • Rear Large Bushing Metal Casing Height: 59.2 mm
3. Elastomeric Component & Bushing Specifications
  • Material Compound: High-durometer vulcanized natural rubber (NR) bonded to carbon steel inner and outer sleeves.
  • Bushing Sub-Components (For Independent Pressing/Rebuilds):
    • Small Front Bushing Ref: 48654-12120 / RU-357 (Dimensions: 14.2mm ID × 39.0mm OD × 59.0mm Length)
    • Large Rear Bushing Ref: 48655-12170 / RU-385 / TAB-026 (Dimensions: 14.5mm ID × 68.5mm OD × 60.0mm Length)
4. Platform Cross-Compatibility
  • The T240 Allion lower control arm shares an identical structural chassis footprint and geometry with the Toyota Premio (T240), Toyota Wish (ANE10/ZNE10), Toyota Corolla (NZE121/ZZE122), and the Toyota Matrix/Voltz (ZZE130) platform variations of the same production era.

Toyota Premio 240 Lower Control Arms

KSh4,000.00
Toyota Premio 240 Series Lower Control Arm Technical Specifications
The front lower control arms for the first-generation Toyota Premio 240 series (chassis codes: NZT240, ZZT240, AZT240, ZZT245 [4WD], production range 2001–2007) feature a classic L-shaped MacPherson strut wishbone layout. This component structurally anchors the front steering knuckle assembly to the vehicle's engine crossmember subframe.
1. Core Part Identification & OEM Numbers
  • Right Hand (RH) Front Lower Control Arm:
    • 48068-20400 (Primary factory baseline number)
    • Interchangeable Structural Refs: 48068-02050, 48068-12220, 48068-0M010
  • Left Hand (LH) Front Lower Control Arm:
    • 48069-20400
    • Interchangeable Structural Refs: 48069-02050, 48069-12220, 48069-0M010
  • Component Weight: Approximately 3.39 kg per side (complete stamped assembly with bushings pressed).
2. Dimensional & Physical Parameters
  • Structural Frame Material: Stamped heavy-gauge cold-rolled carbon sheet steel.
  • Chassis Attachment Layout: 3-Point orientation (Inner forward horizontal bushing + Inner rear vertical trailing bushing + Outer steering knuckle ball joint seat).
  • Bushing Internal Steel Sleeve Dimensions:
    • Forward Horizontal Bolt Sleeve (Inner Diameter): 14.2 mm (Designed for an M14 pivot bolt)
    • Rear Vertical Trailing Bush Sleeve (Inner Diameter): 14.5 mm
  • Rear Large Bushing Outer Barrel Diameter (OD): 68.5 mm
  • Rear Large Bushing Metal Casing Height: 59.2 mm
3. Elastomeric Component & Bushing Specifications
  • Material Compound: High-durometer vulcanized natural rubber (NR) bonded to carbon steel sleeves.
  • Bushing Sub-Components (For Independent Pressing/Rebuilds):
    • Small Front Bushing Ref: RU-357 / 48654-12120 (Dimensions: 14.2mm ID × 39.0mm OD × 59.0mm Length)
    • Large Rear Bushing Ref: RU-385 / TAB-026 / 48655-12170 (Dimensions: 14.5mm ID × 68.5mm OD × 60.0mm Length)
4. Platform Cross-Compatibility
  • The T240 Premio lower control arm shares an identical structural chassis footprint with the Toyota Allion (T240), Toyota Wish (ANE10/ZNE10), Toyota Corolla (NZE121/ZZE122), and the Toyota Matrix/Voltz (ZZE130) platform variants of the same manufacturing era.

Toyota Premio 260 Lower Control Arms

KSh4,000.00
Toyota Premio 260 Series Lower Control Arm Technical Specifications
The front lower control arms for the second-generation Toyota Premio 260 series (chassis codes: NZT260, ZRT260, ZRT261, ZRT265, production range 2007–2021) feature an L-shaped, conventional MacPherson strut lower wishbone architecture. The assembly connects the steering knuckle to the vehicle’s front subframe channel. [1, 2, 3]
1. Core Part Identification & OEM Numbers
  • Right Hand (RH) Front Lower Control Arm:
    • 48068-47040 (Standard factory production number)
    • Aftermarket Cross-Ref: MA-9418R (Masuma), 33 10 9068 (SWAG) [1, 2, 3]
  • Left Hand (LH) Front Lower Control Arm:
    • 48069-47040 / 48069-47041
    • Aftermarket Cross-Ref: MA-9418L (Masuma), 33 10 9069 (SWAG) [1, 2, 3]
  • Component Configuration: Shipped structurally as an arm assembly with pre-pressed rubber bushings, but typically excluding the lower ball joint hardware unless explicitly designated. [1]
2. Dimensional & Physical Parameters
  • Structural Material: Stamped structural sheet carbon steel. [1]
  • Mounting Configuration: 3-Point orientation (Inner forward pivot bush + Inner rear vertical pivot bush + Outer ball joint receptacle). [1, 2]
  • Inner Bushing Hardware Bore Diameters:
    • Forward horizontal pivot bolt sleeve bore: 14.3 mm
    • Rear vertical trailing bush sleeve bore: 14.5 mm – 14.6 mm [1, 2]
  • Rear Bushing Barrel External Outer Diameter: 68.5 mm [1]
  • Rear Bushing Shell Total Length: 60.0 mm [1]
3. Elastomeric Component & Bushing Specifications
  • Bushing Compound: High-elasticity vulcanized natural rubber (NR) bonded inside carbon steel backing sleeves. [1]
  • Bushing Sub-Components (For Independent Rebuilding):
    • Front Bushing OEM Ref: RU-385
    • Rear Large Bushing OEM Ref: RU-386 / TAB-026 [1, 2]
4. Drivetrain Layout Variations
  • 2WD / FWD Base Variations (NZT260, ZRT260, ZRT261): Feature the baseline lightweight stamping profile intended for standard road clearances. [1, 2]
  • 4WD Variations (ZRT265): Utilize modified clearance contours along the rear inner arm radius to accommodate structural axle separation and intermediate transfer shaft geometries.

Toyota Axio 161 Model 2015 Rear Wheel Hubs Bearing

KSh5,000.00
Toyota Corolla Axio NZE161 (2015) Rear Wheel Hub Bearing Technical Specifications
The rear wheel hub assembly for the 2015 Toyota Corolla Axio (Chassis code: NZE161, 2WD Front-Wheel Drive layout) is a complete, unitized Generation 3 modular bolt-on hub assembly. The wheel bearing, mounting flange, and electronic braking system sensors are pre-sealed and integrated into a single non-serviceable cartridge. [1, 2]
1. Core Part Identification & OEM Numbers
  • OEM Part Numbers:
    • 42450-52060 (Primary assembly number)
    • 42450-52061 (Superseded / Updated factory specification)
    • 42410-52060 / 42410-52061 [1]
  • Industry/Aftermarket Reference: PHU2370 / MW-11529 [1, 2]
  • Component Class: Generation 3 Double-Row Ball-Type Hub Unit. [1]
2. Dimensional & Physical Parameters
  • Pitch Circle Diameter (PCD / Lug Pattern): 4 × 100 mm
  • Hub Center Pilot Bore Diameter: 54.1 mm
  • Flange Outer Diameter: 135 mm
  • Internal Bore Diameter (Bearing Inner Diameter): 30 mm
  • Thread Pitch/Size (Wheel Studs): M12 × 1.5
  • Number of Rim Holes / Studs: 4
  • Brake Setup Configuration: Form-fitted to seat flush against standard rear brake drum systems.
  • Weight: Approximately 2.58 kg. [1, 2, 3, 4]
3. Electrical ABS Sensor Integration
  • ABS System Type: Magnetized active wheel speed encoder ring embedded directly into the bearing's inner rubber sealing lip.
  • Signal Mechanism: Tracks vehicle wheel velocity via an external active magnetic sensor bolted to the stationary axle housing. [1, 2]
4. Axle Mounting Mechanics
  • Drive Configuration (NZE161): 2WD/FWD non-driven solid layout. The center bore remains completely smooth with no inner drive splines.
  • Mounting Interface: Anchors to the rear trailing arm stub axle axle carrier flange using a standard 4-bolt backing arrangement (Bolt part numbers: 42421E / 42422A).[1, 2, 3]

Toyota Fielder 161 Model 2015 Rear Wheel Hubs Bearing

KSh5,000.00
Toyota Corolla Fielder NZE161 (2015) Rear Wheel Hub Bearing Technical Specifications
The rear wheel hub assembly for the 2015 Toyota Corolla Fielder (Chassis code: NZE161 / NZE161G, 2WD Front-Wheel Drive platform) is a fully unitized, non-serviceable Generation 3 hub cartridge. The assembly integrates the wheel flange, dual-row pre-loaded bearings, and electronic ABS braking components into a single bolt-on housing.
1. Core Part Identification & OEM Numbers
  • OEM Part Numbers:
    • 42450-52060 (Standard factory production number)
    • 42450-52061 (Superseded/Updated factory spec)
    • 42410-52060 / 42410-52061
  • Industry/Aftermarket Cross-References: PHU2370 / MW-11529 / 512370
  • Assembly Layout: Generation 3 Hub Unit (Integrated inner and outer bearing races with dual structural flanges).
2. Dimensional & Physical Parameters
  • Pitch Circle Diameter (PCD): 4 × 100 mm
  • Hub Center Pilot Bore Diameter: 54.1 mm
  • Flange Outer Diameter: 135.0 mm
  • Wheel Stud Threads: M12 × 1.5
  • Number of Flange Studs/Holes: 4
  • Brake Configuration Interfacing: Engineered exclusively for standard rear drum brake configurations.
  • Inner Hub Configuration: Solid/Smooth center bore housing (No internal splines; exclusive to 2WD/FWD applications).
3. Bearing Internal Design Specs
  • Bearing Construction Type: Double-row, maintenance-free angular contact ball bearing.
  • Lubrication/Seal Dynamics: Factory pre-loaded with premium high-temperature wheel bearing grease; fully enclosed with dual-lip synthetic rubber sealing rings to mitigate debris ingress.
4. Electrical ABS Sensor Integration
  • ABS Technology: Pre-installed magnetic active wheel speed encoder ring embedded directly behind the bearing's internal rubber sealing lip.
  • Signal Mechanism: Reads vehicle speed via an external active magnetic sensor anchored to the stationary axle trailing arm frame.

Toyota Axio Model 2007-2012 Engine Mountain

KSh4,000.00
Toyota Corolla Axio (2007–2012) Engine Mount Technical Specifications
The Toyota Corolla Axio spanning the 2007–2012 production timeline belongs to the E140 platform generation (chassis codes: NZE141, NZE144, ZRE142, ZRE144). It utilizes a 4-point structural engine suspension matrix designed to handle transverse powertrain configurations. [1, 2, 3]
1. Component Matrix & Factory Part Numbers
  • Right-Hand Side (RH) Engine Mount:
    • Type: Liquid-filled hydro-elastic engine cushion assembly (utilizes specialized hydraulic oil internals to suppress low-frequency structural powertrain shudder at idle).
    • OEM Part Numbers: 12305-21300 / 12305-21220 (1.5L 1NZ-FE); 12305-37091 (1.8L 2ZR-FE / 2ZR-FAE). [1, 2]
  • Left-Hand Side (LH) Gearbox/Transmission Mount:
    • Type: High-damping rubber-to-metal isolator stabilizing the transmission case assembly.
    • OEM Part Numbers: 12372-21150 / 12372-21240 (CVT and Manual variants). [1, 2]
  • Rear Engine Torque Rod/Steady Mount:
    • Type: Longitudinal roll-control torque stopper (prevents back-and-forth rotational engine displacement under clutch release or rapid deceleration).
    • OEM Part Numbers: 12371-21150 / 12371-21250. [1]
  • Front Engine Mount Buffer:
    • Type: Snubber structural damper.
    • OEM Part Number: 12361-21040 / 12361-21050. [1]
2. Material Composition & Structural Standards
  • Chassis Core Framing: Robotic MIG-welded stamped high-tensile carbon steel housings mated to structural cast-aluminum block-side mounting brackets. [1]
  • Elastomeric Core: Vulcanized natural rubber (NBR/NR matrix) engineered for continuous oil resistance and high thermal stability within the engine bay. [1, 2]
  • Dampening Medium: Glycol-based fluid buffer built directly into the internal chamber of the RH passenger-side assembly. [1]
3. Drivetrain & Layout Fitment Metrics
  • 2WD / FF Variants (NZE141, ZRE142): Utilize flat, non-extended rear roll isolation brackets that anchor directly into the front crossmember subframe channel. [1, 2]
  • 4WD Variants (NZE144, ZRE144): Employ a modified clearance geometry bracket setup on the rear mount assembly to provide necessary spatial clearance for the transfer case output flange and intermediate drive shafts. [1]

Toyota Fielder Model 2005 Engine Mountain

KSh4,000.00
Toyota Corolla Fielder (2005) Engine Mount Technical Specifications
The 2005 Toyota Corolla Fielder (First Generation, E120 series; chassis codes like NZE121G, ZZE122G, CE121G) features a 4-point engine mounting matrix (front, rear, right/passenger side, and left/driver side transmission mount). The design uses a combination of liquid-filled hydro-elastic dampeners and vulcanized rubber isolators to support transverse engine layouts. [1, 2, 3]
1. Component Breakdown & Factory Part Numbers
  • Right-Hand Side (RH) Engine Mount:
    • Type: Hydraulic-insulator cushion assembly (fluid-filled to isolate low-frequency engine block vibration at idle).
    • OEM Reference: 12305-21130 / 12305-21160 (Engine type: 1NZ-FE 1.5L). [1, 2]
  • Left-Hand Side (LH) Transmission Mount:
    • Type: Transverse rubber-to-metal isolator assembly supporting the gearbox housing shell.
    • OEM Reference: 12372-22080 / 12372-21110. [1]
  • Rear Engine Torque Mount:
    • Type: Anti-torque roll rubber bush stabilizer (controls forward/backward engine pitching under acceleration/braking forces).
    • OEM Reference: 12371-22170 (2WD layouts) or 12371-28070 (Diesel CE121 variants). [1, 2, 3]
  • Front Engine Stop Mount:
    • Type: Longitudinal movement restrictor.
    • OEM Reference: 12361-21020. [1]
2. Engineering & Material Standards
  • Structural Housing Material: Cold-rolled heavy-gauge carbon steel framing coupled with die-cast aluminum sub-brackets.
  • Elastomeric Element: High-tensile vulcanized natural rubber (NR) specialized to optimize shore hardness against under-hood heat cycles.
  • Standard Fastening Threads: Metric coarse thread matrix (predominantly M10 × 1.25 body frame bolts and M12 × 1.25 engine bracket anchoring studs). [1]
3. Application Variations by Engine Type
  • 1NZ-FE (1.5L Petrol) / 1ZZ-FE (1.8L Petrol): Share lightweight aluminum engine bracket configurations interacting with fluid-dampened RH engine bays. [1, 2, 3]
  • 3C-E (2.2L Diesel Variant - CE121G): Employs distinct high-durometer solid rubber compound mounts with upgraded metal frame thickness to isolate standard high-torque diesel harmonic vibrations. [1, 2]

Mazda Demio Model 2010-2018 Engine Mountain

KSh7,500.00
Mazda Demio (2010–2018) Engine Mount Technical Specifications
The Mazda Demio spans two generations during the 2010–2018 timeline: the Third Generation (DE Series, 2007–2014) and the Fourth Generation (DJ Series, 2014–present). Both variations utilize a 3-point layout configuration consisting of an isolated right-hand side engine mount, a left-hand side gearbox/transmission mount, and a rear torque-rod engine stabilizer mount. [1, 2, 3, 4]
1. Third Generation (DE Series: 2010–2014) Specifications
  • Chassis System Codes: DE3FS, DE5FS, DE3AS, DEJFS [1]
  • Engine Codes Covered: 1.3L ZJ-VE, 1.3L P3-VPS (SkyActiv-G), 1.5L ZY-VE [1]
  • Mounting Architecture Components:
    • Right-Hand Side (RH) Engine Mount: Hydro-elastic cushion mount filled with glycol fluid designed to dampen structural frequencies.
      • OEM Factory Ref: D652-39-060 / D652-39-060H
    • Left-Hand Side (LH) Gearbox/Transmission Mount: Multi-plate rubber-to-metal bracket designed for transmission casing isolation.
      • OEM Factory Ref: D653-39-070 (CVT models) / D651-39-070 (Manual transmission)
    • Rear (Lower Trailing) Engine Torque Mount: Solid molded elastomer bracket managing rotational engine twist under heavy acceleration.
      • OEM Factory Ref: D651-39-040 / D653-39-04X [1, 2, 3, 4, 5, 6, 7, 8]
2. Fourth Generation (DJ Series: 2014–2018) Specifications
  • Chassis System Codes: DJ3FS, DJ3AS, DJ5FS, DJ5AS [1]
  • Engine Codes Covered: 1.3L P3-VPS, 1.5L P5-VPS (SkyActiv-G), 1.5L S5-DPTS (SkyActiv-D Diesel) [1]
  • Mounting Architecture Components:
    • Right-Hand Side (RH) Engine Mount: Heavy-duty fluid-filled hydraulic isolator structurally upgraded to manage the higher torque load of SkyActiv setups.
      • OEM Factory Ref: D10E-39-060 / DA6V-39-060
    • Left-Hand Side (LH) Gearbox/Transmission Mount: Top-bracket multi-point bushing isolator.
      • OEM Factory Ref: D10G-39-070
    • Rear (Lower Trailing) Engine Torque Mount: Center anti-twist rod connecting the lower engine block casting to the vehicle's front subframe assembly.
      • OEM Factory Ref: D10E-39-040 [1, 2, 3]
3. Hardware and Material Characteristics
  • Structural Composition: Stamped carbon steel structural arms integrated with vulcanized natural rubber (NR) dampening material or internal hydraulic fluid compartments.
  • Standard Fastener Thread Sizes: M10 × 1.5 frame attachment threads and M12 × 1.25 engine block through-stud threads. [1, 2, 3]

Toyota Passo B2050 Rear Wheel Hub

KSh5,000.00
Toyota Passo Rear Wheel Hub (B2050 Series) Technical Specifications
The rear wheel hub assembly for the Toyota Passo featuring the B2050 identifier (associated with second and third-generation platforms like the KGC30, NGC30, and M700 series) is a pre-adjusted, unitized Generation 3 wheel hub assembly. It natively integrates the wheel flange, dual-row angular bearings, and electronics into a single bolt-on cartridge. [1]
1. Core Part Identification & OEM Numbers
  • OEM Part Numbers:
    • 42410-B2050 (Primary assembly number)
    • 89411-B2050 (Factory part model reference stamped on the casing) [1, 2, 3]
  • Industry/Aftermarket Cross-References: HUB200T-3 [1]
  • Assembly Layout: Hub Unit Generation 3 (One-piece fully sealed unit with integrated mounting flange and sensor tracking).
2. Dimensional & Physical Parameters
  • Pitch Circle Diameter (PCD): 4 × 100 mm
  • Outer Flange Diameter (Ø): 130.0 mm
  • Hub Assembly Width: 67.0 mm
  • Number of Rim/Wheel Bores: 4 threaded stud positions
  • Brake Setup Compatibility: Built with an integrated rear drum backing face to align squarely inside the vehicle's drum brake layout. [1, 2, 3, 4, 5]
3. Electrical Sensor Integration
  • ABS System Type: Magnetized active wheel speed encoder ring fully enclosed inside the bearing seal.
  • Terminal Interface: 2-Pin (2P) electronic plug connector reading directly off the unit. [1, 2]
4. Axle & Drive Geometry**
  • 2WD / FWD Layout (e.g., KGC30-FF): Non-driven configuration featuring a solid inner bore. It anchors straight to the trailing rear axle assembly using a standard 4-bolt configuration. [1, 2]

Toyota Markx Rear Calipers

KSh6,500.00
Toyota Mark X Rear Brake Caliper Technical Specifications
The factory rear brake caliper architecture for the Toyota Mark X (covering both the GRX120 [2004–2009] and GRX130 [2009–2019] platforms) relies on a single-piston floating design engineered by ADVICS. [1]
1. Core Actuation & Piston Metrics
  • Caliper Design Type: Single-piston sliding/floating caliper layout.
  • Piston Diameter: 43.0 mm
  • Piston Repair Kit Ref: 04479-53070 / 47731B (Individual piston core).
  • Caliper Weight: Approximately 2.96 kg per side assembly (with carrier bracket). [1, 2, 3, 4]
2. Factory Component & OE Identification
  • Right Hand (RH) Cylinder Assembly OE:
    • 47830-53050
    • 47830-53051 [1, 2]
  • Left Hand (LH) Cylinder Assembly OE:
    • 47850-53051
    • 47750-30521 [1, 2]
  • Brake System Manufacturer: ADVICS Co., Ltd. [1, 2]
3. Rotor & Pad Interfacing Parameters
  • Compatible Brake Disc Thickness: 10.0 mm (Standard solid rear rotor layout).
  • Factory Caliper Designation Stamp: Fits standard 40 Y1 brake hardware classifications.
  • Compatible Brake Pad Kit OEM: 04466-30210 / 04466-30230. [1, 2, 3, 4, 5]
4. Mounting & Slide Guide Hardware Layout
  • Guide Pin Configuration: Two-part slide pins featuring Pin Cylinder Slide No.1 (47814-30300) paired with specialized dampening slide bushes (47769-30300) to alleviate low-frequency brake groan.
  • Hexagon Mounting Bolts: M10 hex shoulder fastening bolts (Part 90105-10525). [1]

Toyota Fielder Model 2014-2018 Rear Wheel Hubs

KSh5,000.00
1. Core Part Identification & OEM Numbers
  • OEM Part Numbers:
    • 42450-52060 (Standard factory spec)
    • 42450-52061 (Superseded/Updated factory spec)
    • 42410-52060 / 42410-52061 [1, 2]
  • Industry/Aftermarket Reference: PHU2370 / MW-11529
  • Assembly Layout: One-piece unitized assembly housing both the hub mechanism and pre-loaded internal bearings. [1]
2. Dimensional & Physical Parameters
  • Pitch Circle Diameter (PCD): 4 × 100 mm
  • Hub Center Pilot Bore: 54.1 mm
  • Flange Outer Diameter: 135.0 mm
  • Wheel Stud Threads: M12 × 1.5
  • Number of Flange Stud Holes: 4
  • Brake Configuration Compatibility: Form-fitted specifically to interface with standard rear drum brake systems. [1, 2, 3]
3. Electrical Sensor Integration
  • ABS Technology: Pre-installed magnetic active encoder ring encased inside the sealed assembly bearing lip.
  • Signal Pickup: Interfaces directly with the axle-mounted external active wheel speed sensor reading off the internal magnetic tracking ring. [1]
4. Axle & Drive Configuration Mechanics
  • 2WD / FWD Variants (NZE161G, NRE161G, ZRE162G, NKE165G): Features a smooth inner bore housing with a flat rear mounting surface. It unbolts directly from the trailing arm axle assembly using 4 backing bolts per side (Bolt OEM Ref: 90105-12350). [1, 2]
  • 4WD Variants (NZE164G): Engineered with an internal female-splined center bore tracking all the way through the hub core to receive the rear CV drive axle shaft spindle and its outer locknut.

Toyota Axio Model 2015-2018 Rear Wheel Hub

KSh5,000.00
Toyota Corolla Axio (2015–2018) Rear Wheel Hub Technical Specifications
The rear wheel hub assembly for the E160 generation Toyota Corolla Axio (chassis codes: NZE161, NRE161, NKE165 [Hybrid], production range 2015–2018) is a completely sealed, unitized hub and bearing mechanism. [1, 2]
1. Core Part Identification & OEM Numbers
  • OEM Part Numbers:
    • 42450-52060
    • 42450-52061 (Updated / Superseded OEM variation)
    • 42410-52060 [1, 2, 3, 4, 5]
  • Industry/Aftermarket Cross-Reference: PHU2370 / MW-11529 [1, 2]
  • Assembly Type: Hub Unit Generation 3 (Integrated double-row angular contact bearing with a integrated mounting flange and ABS wheel speed encoder ring). [1, 2, 3]
2. Dimensional & Physical Parameters
  • Bolt Pattern (PCD): 4 × 100 mm
  • Hub Center Bore Diameter: 54.1 mm
  • Outer Flange Diameter: 135 mm
  • Thread Size (Wheel Studs): M12 × 1.5
  • Number of Flange Splines/Holes: 4 wheel stud holes.
  • Brake Setup Compatibility: Engineered to seat natively with standard rear drum brake systems. [1, 2, 3, 4]
3. Electrical Sensor Integration
  • ABS System Type: Integrated magnetic encoder ring embedded directly inside the pre-sealed bearing casing.
  • Sensor Configuration: Active wheel speed sensor reads directly off the inner magnetic tracking ring. [1, 2]
4. Axle & Drive Type Specifics
  • 2WD / FWD Models (NZE161, NRE161, NKE165): Uses a flat backing-plate surface that mounts directly onto the rear trailing axle carrier via a standard 4-bolt layout. No center drive axle splines inside the hub bore. [1]
  • 4WD Models (NZE164): Features an internal splined center bore passing all the way through the hub to receive the rear CV drive axle shaft spindle.

Toyota Belta Rear Wheel Hubs

KSh5,000.00
1. Core Part Numbers & Identification
  • OEM Part Numbers:
    • 42450-52060 (Standard 2WD models, both Right-Hand and Left-Hand sides)
    • 42410-52060 [1, 2, 3, 4]
  • Industry/Aftermarket Reference: PHU2370 [1]
  • Layout Configuration: One-piece integrated unit (Hub + Bearing + ABS sensor ring). [1, 2]
2. Dimensional & Physical Parameters
  • Bolt Pattern (PCD): 4 × 100 mm
  • Number of Flange Holes / Studs: 4 holes
  • Brake Setup Compatibility: Integrated layout matching standard rear drum brakes.
  • Bearing Type: Double-row maintenance-free angular contact ball bearing (BFC/BWD designation), completely pre-sealed and pre-loaded from the manufacturer.
  • Weight: Approximately 2.09 kg per hub assembly. [1, 2, 3]
3. Fitment Variations By Chassis Type
  • FWD / 2WD Models (KSP92, SCP92): Utilizes standard axle-mounted flange unbolting mechanics via 4 backing bolts per side (Bolt part number: 90105-12350). [1, 2]
  • 4WD Models (NCP96): Features a splined inner bore configuration built to accommodate the rear CV drive shaft axle layout and a locking rear axle shaft spindle nut. [1, 2]

Toyota Vits Rear Wheel Hubs

KSh5,000.00
Hub & Bearing Unit Architecture
  • Component Design Style: Generation 3 (Gen 3) Hub Assembly Unit. The double-row ball bearing, wheel hub flange, inner race, and digital speed sensor form a single, factory-sealed, non-serviceable component.
  • Drive Type Configuration: 2WD / 4x2 standard layouts.
  • Braking Compatibility: Engine-matched for standard drum brake setups (mounts flush behind the rear brake drum backplate).
  • ABS Sensor Integration: Integrated internal magnetic encoder ring with an external plug-in connector terminal molded into the back plate of the hub housing.
Dimensional Specifications
  • Wheel Bolt Pattern / PCD: 4 x 100 mm
  • Number of Hub Wheel Studs: 4 pre-installed M12 x 1.5 studs
  • Hub Center Pilot Diameter (Center Bore): 54.1 mm
  • Axle Beam Mounting Flange: 4-bolt rectangular symmetrical mounting pattern.
Fastener & Torque Specifications
  • Hub Flange Unit-to-Axle Beam Mounting Bolts (4x): 80 Nm (59 ft-lbs) — Note: These fasteners pass through the rear brake backing plate to anchor the assembly directly to the rear torsion axle beam.
  • Wheel Lug Nuts (Road Wheel to Hub Studs): 103 Nm (76 ft-lbs)
  • Maximum Factory Allowable Hub Axle Backlash (End Play): 0.05 mm (0.0020 inch) max

Toyota Fielder 161 Rear Wheel Hubs

KSh5,000.00
Hub & Bearing Unit Architecture
  • Component Design Style: Generation 3 (Gen 3) Modular Hub Assembly Unit. The wheel bearing, hub flange, inner race, and integrated ABS speed sensor are structurally built into a sealed, non-serviceable assembly. [1, 2]
  • Drive Type Configuration: 2WD / 4x2 standard layouts. [1, 2]
  • Braking Integration: Designed primarily for drum brake setups (fits directly behind the rear brake drum sub-assembly). [1, 2]
  • Factory Genuine OEM Part Reference:
    • 42450-52060
    • 42450-52061 [1, 2, 3, 4]
  • ABS System Integration: Integrated internal multi-pole electronic magnetic sensor ring within the hub unit housing. [1]
Dimensional Specifications
  • Wheel Bolt Pattern / PCD: 4 x 100 mm
  • Number of Hub Wheel Studs: 4 pre-installed studs
  • Hub Center Pilot Diameter (Bore): 54.1 mm
  • Mounting Configuration: 4-bolt symmetrical diamond mounting flange on the rear axle beam/carrier. [1, 2, 3, 4, 5]
Fastener & Torque Specifications
  • Rear Hub Bearing Case-to-Axle Beam Bolts (4x): 80 Nm to 90 Nm (59 to 67 ft-lbs)
  • Wheel Lug Nuts (Road Wheel to Flange Studs): 103 Nm (76 ft-lbs)
  • Maximum Factory Allowable Hub Axle Backlash (End Play): 0.05 mm (0.0020 inch) max [1, 2, 3, 4]

Toyota Nze Engine Mountain

KSh4,000.00
Engine Mount System Layout
  • Total Number of Mounts: 4 structural mounting units.
  • Mounting Positions & Configuration:
    • Front Engine Mount: Solid rubber cushion assembly positioned on the front radiator core crossmember to arrest forward rotational pitch.
    • Right-Hand (RH) Engine Mount: Heavy-duty rubber-metal isolation mount bolted to the engine timing chain cover bracket. This acts as the structural anchor for vertical engine mass.
    • Left-Hand (LH) Transmission Mount: Isolation block securing the gearbox/transaxle casing directly to the structural side-frame rail.
    • Rear Engine Mount: High-load torque-reaction insulator anchoring the rear differential/gearbox assembly to the rear engine subframe to eliminate longitudinal twist during gear shifts and acceleration.
  • Material Architecture: High-damping vulcanized synthetic rubber bonded to die-cast aluminum and heavy-gauge stamped steel mounting shells.
Engine Mount Fastener Torque Specifications
  • Right-Hand (RH) Mount Through-Bolt to Engine Bracket: 95 Nm (70 ft-lbs)
  • Right-Hand (RH) Mount Base Plate to Body Bracket Bolts: 52 Nm (38 ft-lbs)
  • Left-Hand (LH) Transmission Mount to Transaxle Bracket Bolt: 56 Nm (41 ft-lbs)
  • Left-Hand (LH) Transmission Mount Base to Chassis Frame Bolts: 95 Nm (70 ft-lbs)
  • Front Engine Mount Centering Through-Bolt to Crossmember: 95 Nm (70 ft-lbs)
  • Front Engine Mount Bracket to Chassis Frame Bolts: 85 Nm (63 ft-lbs)
  • Rear Engine Mount Longitudinal Through-Bolt: 95 Nm (70 ft-lbs)
  • Rear Engine Mount Bracket to Subframe Structural Bolts: 87 Nm (64 ft-lbs)
Core Engine Specs (NZE121 Platform)
The mounting layout supports the standard transverse inline-4 cylinder block configuration:
  • Engine Code: 1NZ-FE
  • Configuration: Inline 4-Cylinder, 16-Valve DOHC with VVT-i
  • Displacement: 1,496 cc
  • Cylinder Bore x Stroke: 75.0 mm × 84.7 mm
  • Compression Ratio: 10.5:1
  • Peak Power Output: 109 PS (80 kW / 107 HP) @ 6,000 rpm
  • Peak Torque Output: 141 Nm (104 lb-ft) @ 4,200 rpm

Toyota Axiom Engine Mountain

KSh4,000.00
Engine Mount System Layout
  • Total Number of Mounts: 4 structural mounting assemblies. [1]
  • Mounting Positions & Configuration:
    • Front Engine Mount: Solid rubber-to-metal dampening cushion mounted directly onto the front crossmember subframe assembly.
    • Right-Hand (RH) Engine Mount: A high-isolation, liquid-filled hydraulic mount (hydro-mount) attached to the engine's timing chain cover bracket. This is the primary load-bearing mount for engine mass.
    • Left-Hand (LH) Transmission Mount: A structural rubber isolator linking the transaxle/gearbox casing to the main vehicle side-frame rail.
    • Rear Lower Engine Mount: A torque-reaction "dog-bone" style insulator anchoring the rear transmission casing to the subframe to manage longitudinal engine twist during acceleration. [1, 2, 3, 4]
Engine Mount Fastener Torque Specifications
  • Right-Hand (RH) Mount Through-Bolt to Engine Bracket: 95 Nm (70 ft-lbs)
  • Right-Hand (RH) Mount Main Structural Nut (Nut A): 95 Nm (70 ft-lbs)
  • Right-Hand (RH) Mount Insulator Stopper Nut (Nut B): 52 Nm (38 ft-lbs)
  • Right-Hand (RH) Mount Base Plate to Body Bolts: 95 Nm (70 ft-lbs)
  • Left-Hand (LH) Transmission Mount to Transaxle Bracket: 56 Nm (41 ft-lbs)
  • Left-Hand (LH) Transmission Mount to Chassis Body Bolts: 95 Nm (70 ft-lbs)
  • Front Engine Mount Insulator to Crossmember Bolt: 95 Nm (70 ft-lbs)
  • Front Engine Mount Bracket to Chassis Body: 85 Nm (63 ft-lbs)
  • Rear Lower Engine Mount Through-Bolt to Bracket: 95 Nm (70 ft-lbs)
  • Front Subframe Crossmember Assembly to Body Bolts: 99 Nm (73 ft-lbs) [1, 2]
Supported Engine Platform Configurations
The structural design patterns accommodate the core transverse inline-4 cylinder blocks utilized throughout the Axio production cycle: [1]
Engineering Metric 1.5L 1NZ-FE Powertrain 1.5L 2NR-FKE Powertrain
Configuration Inline 4-Cylinder, 16-Valve DOHC Inline 4-Cylinder, 16-Valve DOHC
Cam Timing Tech VVT-i (Variable Valve Timing) Dual VVT-iE (Electric Intake, Hyd. Exhaust)
Displacement 1,496 cc 1,496 cc
Bore x Stroke 75.0 mm × 84.7 mm 72.5 mm × 90.6 mm
Compression Ratio 10.5:1 13.5:1 (Atkinson-cycle setup)
Peak Power Output 109–110 PS @ 6,000 rpm 109 PS (80 kW) @ 6,000 rpm
Peak Torque Output 140–143 Nm @ 4,200–4,400 rpm 136 Nm @ 4,400 rpm

Suzuki Alto Model 2018 Front Shocks

KSh5,000.00

Product Description: Suzuki Alto / Alto Works / Alto Turbo RS (HA36S & HA36V Chassis, 2014–2021 / 2018 Model Year) Complete Front Shock Absorber Set

Overview

The Front Shock Absorber Set for the 2018 Suzuki Alto (HA36S 2WD & HA36V Van / 4WD Chassis, 8th Generation 2014–2021 with 660cc R06A Naturally Aspirated & Turbocharged Powertrains) is an OEM-spec, gas-pressurized front strut replacement set engineered to restore light, responsive steering control, eliminate nose-diving, and absorb harsh urban road impacts. Specially calibrated for the lightweight, high-rigidity HEARTECT platform architecture of the HA36 Suzuki Alto, these twin-tube dampers restore factory ride stability and cornering balance.

Technical Specifications & Characteristics

  • Vehicle Compatibility:

    • 8th Generation Suzuki Alto: HA36S (2WD Passenger / Works / Turbo RS) & HA36V (2WD / 4WD Commercial Van) (2014–2021 / 2018 Model Year) (Also cross-fits twin platform Mazda Carol HB36S).

  • Position: Front Axle (Left Front LH & Right Front RH specific).

  • Operating System: Twin-Tube Low-Pressure Nitrogen Gas-Charged Hydraulic Struts.

  • Damping Medium: High-viscosity all-weather synthetic hydraulic fluid charged with nitrogen gas to prevent fluid foaming, internal aeration, and thermal performance fade during daily urban driving.

  • Build Quality: High-tensile seamless steel body cylinder, micro-polished induction-hardened chrome piston rod, and multi-lip NOK fluid seals to eliminate oil leaks.

  • Mounting Configuration: Direct factory bolt-on fitment attaching to upper strut top mounts, lower steering knuckle clevis bolts, stabilizer link brackets, and brake hose/ABS sensor wiring clips.

Key Features & Performance Benefits

  1. Stops Front-End Nose-Diving & Pitching: Restores firm front rebound control, eliminating forward pitching under braking and controlling body lean through tight turns.

  2. Absorbs Potholes & Rough Road Chatter: Dampens sharp pavement chatter, expansion joints, and speed humps, preserving a comfortable ride for driver and front passenger.

  3. Restores Precise Steering & Wheel Alignment: Holds front camber and toe angles steady under dynamic travel, protecting front tires from patchy tread cupping and uneven shoulder wear.

  4. Reinforced Lower Knuckle Brackets: Heavy-duty lower clevis brackets withstand severe road impacts and maintain rigid steering geometry alignment.

Variant & Fitment Notes (2WD HA36S vs. 4WD HA36V / Standard vs. Works Turbo RS)

Important: While standard HA36S Alto 2WD models share identical front strut body dimensions, 4WD variants and performance-oriented Alto Turbo RS / Alto Works models feature firmer damper valving and altered spring seat heights:

  • Standard 2WD (HA36S / HA36V) OEM Reference:

    • Front Right (RH) Strut: 41601-74P00, 41601-74P10, 41601-74P01

    • Front Left (LH) Strut: 41602-74P00, 41602-74P10, 41602-74P01

  • Alto Turbo RS / Works (HA36S Sport Trim) OEM Reference:

    • Front Right (RH) Strut: 41601-74P50, 41601-74P60

    • Front Left (LH) Strut: 41602-74P50, 41602-74P60

  • Popular Aftermarket Brands: KYB (Excel-G / New SR Special NST5628R/L for HA36S), Tokico, Monroe OESpectrum, GAB, Febest, and SenSen.

Honda N Wagn Front Shocks

KSh5,000.00
Strut Architecture & Design
  • Suspension Type: Independent MacPherson strut suspension.
  • Dampening System: Hydraulic twin-tube, low-pressure nitrogen gas-charged strut assembly.
  • Mounting Configuration:
    • Top Mount: 3-bolt upper strut mount plate with an integrated rubber isolation spring seat and strut bearing.
    • Bottom Mount: Rigid 2-bolt clamp bracket welded to the outer shell casing, clamping directly onto the front steering knuckle.
  • Integrated Hardware: Features a welded bracket for the stabilizer link (sway bar end-link) and a mounting clip for the brake hose line.
Dimensional Specifications (660cc S07A / S07B Key Car Chassis)
  • Extended Length: 455 mm to 468 mm (varies marginally between 2WD JH1/JH3 and 4WD JH2/JH4 ride height setups).
  • Collapsed Length: 315 mm to 325 mm.
  • Total Piston Stroke: 140 mm to 143 mm.
  • Piston Rod Diameter: 18.0 mm (high-tensile chrome-plated steel).
  • Outer Cylinder Casing Diameter: 45.0 mm.
Fastener & Torque Specifications
  • Upper Strut Center Piston Rod Nut: 44 Nm (approx. 33 ft-lbs).
  • Upper Strut Mount Base Flange Nuts (To Chassis Body): 34 Nm (approx. 25 ft-lbs).
  • Lower Strut-to-Knuckle Pinch Bolts (M12): 78 Nm to 85 Nm (approx. 58–63 ft-lbs).
  • Stabilizer / Sway Bar Link Nut (To Strut Bracket): 39 Nm (approx. 29 ft-lbs).
  • Front Wheel Lug Nuts (Road Wheel to Hub): 103 Nm (approx. 76 ft-lbs).
Component Mass
  • Average Unit Mass (Dry Strut Assembly): ~3.8 kg to 4.2 kg per side (excluding the coil spring).

Honda Odyssey Rear Shocks Absorbers

KSh8,500.00
Shock Absorber Architecture & Design
  • Suspension Type: Independent multi-link rear suspension or trailing-arm setup (depending on generation).
  • Dampening System: Low-pressure, nitrogen gas-charged twin-tube or mono-tube hydraulic shock absorber.
  • Mounting Configuration:
    • Top Mount: Two-bolt top mounting flange bracket or traditional stem/pin setup passing through the rear chassis tower body.
    • Bottom Mount: Clevis/fork bracket or heavy-duty eyelet sleeve mounted directly to the lower control arm or rear knuckle trailing bracket.
  • Aspiration/Adjustability: Deployed as passive variable dampening units (amplitude reactive dampers) or multi-valve configurations.
Dimensional Specifications (Standard J-Series V6 Generations - RL5/RL6)
  • Extended Length (Mount Center to Center): 520 mm to 545 mm (varying slightly by model year trim levels).
  • Collapsed Length: 345 mm to 365 mm.
  • Total Piston Stroke: 175 mm to 180 mm.
  • Piston Rod Diameter: 14.0 mm to 16.0 mm (high-strength induction hardened steel).
  • Outer Shell Tube Diameter: 45.0 mm to 51.0 mm.
  • Lower Mount Inner Bushing Diameter: 12.2 mm / 14.1 mm (designed for M12/M14 heavy-load shoulder bolts).
Fastener & Torque Specifications
  • Upper Shock Absorber Flange Mounting Bolts (To Body): 59 Nm (approx. 44 ft-lbs).
  • Upper Shock Pin/Stem Locknut (Where Applicable): 29 Nm (approx. 22 ft-lbs).
  • Lower Shock Absorber Mounting Bolt (To Lower Arm): 88 Nm to 98 Nm (approx. 65–72 ft-lbs) — Must be fully tightened only when the vehicle suspension is under full normal load (resting on the ground).
  • Rear Wheel Lug Nuts (Road Wheel to Hub): 108 Nm (approx. 80 ft-lbs).
Component Mass
  • Average Unit Mass (Dry): ~2.4 kg to 2.9 kg per shock absorber unit.

Toyota Passo Rear Shocks Absorbers

KSh2,500.00
Shock Absorber Architecture & Design
  • Suspension Type: Trailing-arm type torsion beam rear suspension.
  • Dampening System: Hydraulic twin-tube, low-pressure gas-charged shock absorber.
  • Mounting Configuration:
    • Top Mount: Pin/stem-type top rod configuration (secured through the inner vehicle wheel-well arch via rubber isolating bushings, steel washers, and a locknut).
    • Bottom Mount: Eyelet sleeve configuration (secured via a horizontal bolt passing through the lower trailing arm bracket).
  • Operation Principle: Double-acting (dampens both compression/jounce and extension/rebound cycles).
Dimensional Specifications (Standard 2WD Variants)
  • Extended Length (Eye-to-Pin Center): 465 mm to 480 mm (depending on specific model year / aftermarket OEM cross-references).
  • Collapsed Length: 305 mm to 315 mm.
  • Total Piston Stroke: 160 mm to 165 mm.
  • Piston Rod Diameter: 12.0 mm.
  • Outer Shell Tube Diameter: 38.0 mm to 42.0 mm.
  • Lower Eyelet Bushing Inner Diameter: 12.1 mm (fits standard M12 shoulder bolt).
Fastener & Torque Specifications
  • Upper Stem/Pin Locknut: 25 Nm (approx. 18 ft-lbs) — Note: Do not over-tighten, as over-compressing the upper rubber isolation bushings leads to premature bushing failure.
  • Lower Eyelet Mounting Bolt (To Trailing Arm): 80 Nm (approx. 59 ft-lbs) — Crucial: This lower bolt must be given its final torque sequence only while the vehicle is resting at its standard static ride height on the ground to prevent bushing twist.
  • Rear Wheel Lug Nuts (Road Wheel to Hub): 103 Nm (approx. 76 ft-lbs).
Cross-Chassis Assembly Weights
  • Average Unit Mass (Dry): ~1.65 kg to 1.85 kg per shock absorber side.

Honda Fit 2012 Engine Mountain

KSh4,000.00
Engine Mount System Layout
  • Total Number of Mounts: 3 structural mounting assemblies [1, 2]
  • Mounting Positions & Configuration:
    • Front / Right-Hand Mount: A heavy-duty, fluid-filled hydraulic isolation mount (hydro-mount) attached to the engine block side. It bears vertical load and dampens mid-to-high frequency block frequencies.
    • Left-Hand Transmission Mount: A solid rubber-metal isolation assembly supporting the gearbox casing to the structural framing.
    • Rear Lower Torque Strut Mount: Known as the "torque rod" or "dog-bone" link. It connects the transmission housing directly back into the front crossmember/subframe to absorb front-to-rear rotational energy during acceleration and engine braking. [1, 2, 3, 4, 5]
  • Isolation Material: Vulcanized synthetic elastomer combined with glycol fluid dampening internals (on the primary side mount). [1]
Engine Mount Fastener Torque Specifications
  • Front Right-Hand Mount (Side Bracket to Block Bolts): 54 Nm (40 ft-lbs)
  • Front Right-Hand Mount (Through-Bolt to Body): 64 Nm (47 ft-lbs)
  • Left-Hand Gearbox Side Mount Through-Bolt: 54 Nm (40 ft-lbs)
  • Rear Lower Torque Strut Mount Horizontal Bolt (To Frame): 83 Nm (approx. 61 ft-lbs)
  • Rear Lower Torque Strut Mount Vertical Bolt (To Bracket): 93 Nm (approx. 68 ft-lbs) [1, 2]
Core Engine Specs (GE6 / GE8 Chassis Variations)
The 2012 model year globally features two primary variants of the Honda L-Series engine family: [1, 2]
Engineering Parameter 1.3L Variant (L13A Engine) 1.5L Variant (L15A Engine)
Engine Code L13A L15A (L15A7 i-VTEC)
Configuration Inline 4-Cylinder, 4-Stroke Inline 4-Cylinder, 4-Stroke
Valvetrain 16-Valve SOHC i-VTEC 16-Valve SOHC i-VTEC
Timing Drive Chain-driven Chain-driven
Displacement 1,339 cc 1,497 cc
Bore x Stroke 73.0 mm × 80.0 mm 73.0 mm × 89.4 mm
Compression Ratio 10.5:1 10.4:1
Maximum Power 100 PS (73 kW / 99 HP) @ 6,000 rpm 117–120 HP (88 kW) @ 6,600 rpm
Maximum Torque 127 Nm @ 4,800 rpm 145 Nm (106 lb-ft) @ 4,800 rpm
Fuel System PGM-FI Multi-Point Injection PGM-FI Multi-Point Injection
Fluid & Service Specs
  • Engine Oil Total Capacity: 3.6 Liters (Refill capacity with filter change) [1]
  • Factory Recommended Grade: API Premium 0W-20 or 5W-30 synthetic oil [1]
  • Valve Clearances (Cold Engines):
    • Intake: 0.15 mm – 0.19 mm
    • Exhaust: 0.26 mm – 0.30 mm [1]
  • Spark Plug Gaps: 1.0 mm – 1.1 mm

Suzuki Wagon R Wheel Hub Bearing

KSh4,000.00
Front Axle Wheel Bearing Specifications
  • Bearing Design Style: Generation 1 (Gen 1) Double-Row Angular Contact Ball Bearing (Sealed, pre-greased, press-in configuration). [1, 2]
  • Core Dimensions (Standard K-Car / MH / Wagon R+ Generations):
    • Inner Diameter (ID): 35.0 mm (Note: Specific older 1.2L Wagon R+ European versions utilize a 42.0 mm ID).
    • Outer Diameter (OD): 61.8 mm (42mm ID variants utilize an 82.0 mm OD).
    • Width / Thickness: 40.0 mm (42mm ID variants utilize a 36.0 mm width). [1, 2]
  • Part Interactivity: Fits symmetric left and right steering knuckles.
  • ABS Integration: Available as standard passive sealed or featuring a built-in magnetic multi-pole ABS encoder ring on the inner seal face, depending on the manufacturing year and trim. [1, 2]
  • Standard Mass / Weight: ~0.43 kg. [1]
Rear Axle Wheel Hub & Bearing Specifications
  • Bearing Design Style: Hub Unit I (Internal double-row setup or integrated wheel hub assembly depending on chassis configuration, e.g., MH21S, MH34S, MH44S). [1, 2]
  • Core Dimensions (Standard Wagon R / Stingray Variations):
    • Inner Diameter (ID): 25.0 mm
    • Outer Diameter (OD): 52.0 mm
    • Width / Thickness: 42.0 mm [1]
  • Wheel Lug Mounting (Flange Type Hubs):
    • Bolt Pattern / PCD: 4 x 100 mm
    • Centering Pilot Diameter: 54.0 mm [1]
  • Total Component Weight: ~0.37 kg [1]
Fastener & Torque Specifications
  • Main Front Axle Center Hub Nut Torque: 175 Nm to 210 Nm (Approx. 129–155 ft-lbs) — Must be torqued to spec while the vehicle is lifted to set the correct non-adjustable internal bearing preload.
  • Rear Axle Hub Nut Torque:
    • For Drum/Spindle Setup: 180 Nm (Approx. 132 ft-lbs)
    • For R+ High-Load Rear Variations: Up to 325 Nm [1]
  • Wheel Lug Nuts (Road Wheel to Hub): 85 Nm to 95 Nm (Approx. 63–70 ft-lbs). [1, 2]
  • Internal Structural Bearing Tolerances: Acceptable factory end play is 0.001 to 0.005 inches (0.025 to 0.127 mm) maximum.
Showing 140 of 639 results
Please select your product
Product has been added to your cart
Compare (0)